JAI TMC-775 User Manual Download Page 29 | Manualshive

Page: 29 / 82

background image

Software Introduction & Installation29

TMC-775/TMC-773

•

Focus In Fine

Pressing and holding this button causes the lens to “focus in” in a slow fashion. Releasing the button causes the
focus to stop. The speed of the focus may be set using the Advanced Setting Menu (see section 4.5)

•

Focus Out Coarse

Pressing and holding this button causes the lens to “focus out” in a rapid fashion. Releasing the button causes the
focus to stop. The speed of the focus may be set using the Advanced Setting Menu (see section 4.5)

•

Focus Out Fine

Pressing and holding this button causes the lens to “focus out” in a slow fashion. Releasing the button causes the
focus to stop. The speed of the focus may be set using the Advanced Setting Menu (see section 4.5)

Note:

This capability requires a lens with a motorized focus control.

4.3.4

Iris Control

The iris control allows you to remotely change the aperture of the lens when properly wired to the 15-pin
connector.

Figure 25.

Iris Control Set

•

Iris Open Coarse

Pressing and holding this button causes the iris to open in a rapid fashion. Releasing the button causes the iris to
stop. The speed of the iris control may be set using the Advanced Setting Menu (see section 4.5)

•

Iris Open Fine

Pressing and holding this button causes the iris to open in a slow fashion. Releasing the button causes the iris to
stop. The speed of the iris control may be set using the Advanced Setting Menu (see section 4.5)

•

Iris Close Coarse

Pressing and holding this button causes the iris to close in a rapid fashion. Releasing the button causes the iris to
stop. The speed of the iris control may be set using the Advanced Setting Menu (see section 4.5)

•

Iris Close Fine

Pressing and holding this button causes the iris to close in a slow fashion. Releasing the button causes the iris to
stop. The speed of the iris control may be set using the Advanced Setting Menu (see section 4.5)

Note:

This capability requires a lens with a motorized iris control.

«
...
27
28
29
30
31
...
»

Summary of Contents for TMC-775



















































































Reviews:

No comments

Related manuals for TMC-775

Brand: D-Link Pages: 16

FL 50 - Hot-shoe clip-on Flash

Brand: Olympus Pages: 18

Brand: Samsung Wisenet Pages: 16

vdp20 vandal dome

Brand: deView electronics Pages: 2

Brand: Siqura Pages: 2

UAV-GA-T-2030TA

Brand: Dahua Pages: 17

Brand: Pix Controller Pages: 21

Brand: Zuden Pages: 19

LoRa Custos WWDLW Series

Brand: UbiTech Pages: 17

Brand: Abus Pages: 18

Brand: Leica Pages: 358

Brand: Velleman Pages: 4

Brand: Wisenet Pages: 2

Brand: Burg Wächter Pages: 21

Brand: Optex Pages: 2

Brand: eLine Pages: 38

Brand: DW Pages: 80

Brand: Super Circuits Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands