JAI LT-200CL User Manual Download | Manualshive

Page: 62 / 65

background image

LT-200CL

61

Appendix

1. Precautions

Personnel not trained in dealing with similar electronic devices should not service this camera.
The camera contains components sensitive to electrostatic discharge. The handling of these
devices should follow the requirements of electrostatic sensitive components.
Do not attempt to disassemble this camera.
Do not expose this camera to rain or moisture.
Do not face this camera towards the sun, extreme bright light or light reflecting objects.
When this camera is not in use, put the supplied protective cap on the lens mount.
Handle this camera with the maximum care.
Operate this camera only from the type of power source indicated on the camera.
Remove power from the camera when changing switch settings.

2. Typical Sensor Characteristics

The image sensors used in the LT-200CL are CMOS type and have been chosen for their superior
performance. There may, however, always be artifacts visible in the scanned image originating
from pixel imperfections in the camera. The Pixel Gain and Pixel Black correction functions will
allow the user to compensate for such artifacts, producing an essentially “flat” image.

3. Caution when mounting a lens on the camera

When mounting a lens on the camera dust particles in the air may settle on the surface of the
lens or the image sensor of the camera. It is therefore important to keep the protective caps on
the lens and on the camera until the lens is mounted. Point the lens mount of the camera
downward to prevent dust particles from landing on the optical surfaces of the camera. This
work should be done in a dust free environment. Do not touch any of the optical surfaces of the
camera or the lens.

4. Caution when mounting the camera

When you mount the camera on your system, please make sure to use screws of the
recommended length described in the following drawing. Longer screws may cause serious
damage to the PCB inside the camera.

Camera chassis

Fixing plate

Mounting the camera to fixing plate

4.5mm　±　0.2mm

«
...
60
61
62
63
64
...
»

Summary of Contents for LT-200CL


































































Reviews:

No comments

Related manuals for LT-200CL

Brand: 2gig Technologies Pages: 8

Brand: 2gig Technologies Pages: 2

Brand: Tamron Pages: 4

Brand: Tamron Pages: 4

Brand: Tamron Pages: 4

Brand: Tamron Pages: 2

Brand: Tamron Pages: 6

Brand: Tamron Pages: 2

Brand: VADDIO Pages: 20

WallVIEW CCU HD-18 HD-SDI

Brand: VADDIO Pages: 18

Brand: VADDIO Pages: 60

ClearSHOT 10 USB

Brand: VADDIO Pages: 62

Brand: VADDIO Pages: 41

Brand: Vacron Pages: 2

CLEARVIEW HD-18

Brand: VADDIO Pages: 4

Brand: Ubiquiti Pages: 24

Brand: FootfallCam Pages: 4

Brand: TPG Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands