JAI LT-200CL User Manual Download

Page: 41 / 65

LT-200CL

after pixel gain
correction

not been finished yet.

1=Succeeded.
2=Error1 – image was too

bright.

3=Error2 s too bright.n has no
4=Error3 – Timeout-error
occurred.

Select pixel black
correction mode

PBC=[Param.]<CR><LF>
PBC?<CR><LF>

0=Off (Bypass)
1=Factory area
2=User area

Run pixel black
correction, store
to user area

PBR=[Param.]<CR><LF>

0=Run pixel black correction,

store to user area

Store in user setting.

Inquire the status
after pixel black
correction

PBS?<CR><LF>

0=Pixel black correction has

not been finished yet.

1=Succeeded.
2=Error1 – image was too

bright.

3=Error2 – image was too
dark.
4=Error3 – Timeout-error

occurred.

G – Saving and loading data in EEPROM

Load Settings
(from Camera
EEPROM)

LD=[Param.]<CR><LF>

0=Factory area
1=User area1
2=User area2

Latest used DATA
AREA will become
default at next
power up.

Save Settings
(to Camera
EEPROM)

SA=[Param.]<CR><LF>

1=User area1
2=User area2

Note the parameter 0 is not
allowed.

EEPROM Current
Area No. Request.

EA?<CR><LF>

0=Factory area
1=User area1
2=User area2

The camera returns
latest used DATA
AREA.

Note: To avoid malfunction, do not attempt writing commands not shown in the above list.

Summary of Contents for LT-200CL


































































Search results

Summary of Contents for LT-200CL

Reviews:

Related manuals for LT-200CL

Brands by name

Popular brands

JAI LT-200CL, User Manual

Search results

Summary of Contents for LT-200CL

Reviews:

Related manuals for LT-200CL

Brands by name

Popular brands