JAI CM-140GE User Manual Download Page 24

Page: 24 / 76

CM-140GE / -RA/-UV / CB-140GE / -RA

- 22 -

7. Image output signal

7.1. Output image

The CCD sensor layout with respect to pixels and lines used in the timing and video full frame read

out is shown below.

1434

1052

1392

1040

OB(7)

Effective Video Output

1392 (H) x 1040 (V)

Pixel (1,1)

G B

DVAL

OB, 4 lines for Vertical
and 16 pixels for
Horizontal can be
transferred on OB
Transfer Mode.

Fig. 15 CCD sensor layout

Important Note: By using the Optical Black (OB) transfer mode, the user can select whether to

include optical black pixels in the image stream.

7.2. Vertical binning (CM-140GE only).

The binning functions can be used to achieve higher frame rate or higher sensitivity. The

drawback is lower resolution.

Vertical binning is done by adding the charge

from pixels in adjacent lines in the horizontal

CCD register.

Fig. 13 shows the binning principle. Resolution

and frame rate for all combinations are shown

in the below table.

Fig.16 CM-140GE binning.

The CM-140GE/-RA/-UV has 2:1 Vertical Binning:

Setting

Value for Register address 0xA084

Resolution (pixels) Frame rate(fps)

Off (no binning)

0x01

1392(h) x 1040(v)

31.08 (UV:16.14)

2:1 binning

0x02

1392(h) x 520(v)

48.86 (UV:25.37).

Xsg1

Video out

No V binning

V binning

Xsg1

Video out

No V binning

V binning

Summary of Contents for CM-140GE













































































Search results

Summary of Contents for CM-140GE

Reviews:

Related manuals for CM-140GE

Brands by name

Popular brands

JAI CM-140GE, User Manual

Search results

Summary of Contents for CM-140GE

Reviews:

Related manuals for CM-140GE

Brands by name

Popular brands