![background image](http://html1.mh-extra.com/html/jai/cm-040mcl-ra/cm-040mcl-ra_user-manual_3225264038.webp)
CM-040MCL /-RA / CB-040MCL /-RA
35
10.2.
Specification table
Specifications
CM-040MCL/-RA
CB-040MCL/-RA
Scanning system
Progressive scan
Frame rate full frame
60.15 frames/sec. Progressive (596 lines/frame)
Pixel clock
33.75 MHz
Line frequency
36.447 kHz (1H = 27.437 µs) (926 pixel clock/line)
CCD sensor
1/2 inch Monochrome ICX415AL
1/2 inch Bayer Color ICX415AQ
Sensing area
6.49 (h) x 4.83 (v) mm 1/2 inch diagonal
Cell size
8.3 (h) x 8.3 (v)
m
Active pixels
776 (h) x 582 (v)
Pixels in video output.
Full Scan
2/3 partial Scan
1/2 partial Scan
1/4 partial Scan
1/8 partial Scan
Vertical Binning
776 (h) x 582 (v) 61 fps. H = 36.447 kHz
776(h) x 390 (v) 87 fps H= 36.447 kHz
776 (h) x 294 (v) 110 fps. H = 36.447 kHz
776(h) x 146 (v) 186 fps. H = 36.447 kHz
776 (h) x 74 (v) 280 fps. H = 36.447 kHz
776 (h) x 291 (v) 111 fps. H = 33.416 kHz ( CM-040MCL/-RA only))
Note: Partial scan and Vertical Binning mode cannot be used at the same time
Sensitivity on sensor (minimum)
0.2 Lux (Max. gain, Shutter OFF, 50%
video )
1.3 Lux (Max. gain, Shutter OFF,50%
Green, w/IR cut filter)
S/N ratio
More than 50 dB (0dB gain)
Digital Video output
Camera Link
8 bit, 10 bit
Camera Link
BAYER 8 bit, 10 bit
Iris video output. Analog
0.7 V p-p
Gain
Manual : -3 to +12 dB
Gamma
γ=1.0
Synchronization
Internal X-tal
Hardware Trigger modes
Edge Pre-Select , Pulse Width Control, RCT
Electronic Shutter
Preset Shutter speed
Programmable exposure
OFF(1/61) and 1/100 to 1/10,000 in 9 steps
2L(54.8µs) to 596 L ( 16.3 ms) in 1L steps
Lens Iris Control
Video control
Control interface
Camera Link
Indicators on rear panel
Power, trigger
Operating temperature
-5
C to +50
C
Humidity
20 – 90% non-condensing
Storage temp/humidity
-25
C to +60
C/20% to 90 % non-condensing
Vibration
10G (20Hz to 200Hz, XYZ)
Shock
70G
Regulatory
CE (EN61000-6-2 and EN61000-6-3), FCC part 15 class B, RoHS, WEEE
Power
12V DC
10%. 5.1 w
Lens mount
C-mount
Rear protrusion on C-mount lens must be less than 10.0mm
Flange back
17.526mm Tolerance 0
~
-0.05mm
Optical Low Pass Filter
Built in (Only for CB-040MCL/040MCL-RA)
Dimensions
CM/CB-040MCL
44 x 29 x 75 mm (W x H x D) excluding protrusions
CM/CB-040MCL-RA
44 x 29 x 93.5 mm (W x H x D) excluding protrusions
Weight
CM/CB-040MCL
125 g
CM/CB-040MCL-RA
155 g
Above specifications are subject to change without notice