1 0 9 6 3 2
1 0 9 6 3 2
ROUGHING-IN
DIMENSIONS
Plumbers' Putty or Caulking
Adjustable Wrench
Phillips Screwdriver
Channel Locks
TOOLS REQUIRED
Tubing Cutter
Regular Screwdriver
Basin Wrench
APPLY SEALANT
OR TEFLON TAPE
2
A FOAM SEAL (1) is installed on underside of FLANGE (2). (Plumbers
Putty may be used in place of FOAM SEAL (1) if desired.)
Apply sealant or Teflon tape to threads of TAILPIECE (10) and
thread into DRAIN BODY (7) making a water tight seal.
Drop FLANGE (2) into LAVATORY DRAIN (3). From below assemble
RUBBER GASKET (4), PLASTIC WASHER (5) and LOCK NUT (6) onto
DRAIN FLANGE (2). Do not tighten fully.
INSTALL POP-UP DRAIN (Lavatory Faucet only)
FIG. 2a
FIG. 2b
FIG. 2c
FIG. 2c
FIG. 2a
FIG. 2b
1
4
3
2
5
6
7
8
6
9
2
Adjust STOPPER (13) height by repositioning POP-UP ROD (16) in SWIVEL (15)
and tightening SET SCREW (18).
Assemble POP-UP SWIVEL (15) to PIVOT ROD (11) but do not tighten.
Drop POP-UP ROD (16) through other hole in POP-UP SWIVEL (15) and
tighten SET SCREW (17)
Assemble PIVOT ROD (11), and PIVOT NUT (12) as shown. Install CONCAVE
WASHER (19) into PIVOT ROD OPENING (9) if not preinstalled. Hand
tighten PIVOT NUT (12). Drop STOPPER (13) into drain.
(
To vandal proof drain rotate STOPPER (13) so PIVOT ROD (11) goes
through EYE (14) of STOPPER (13)
. Make connection to "P" TRAP.
Inspect inside DRAIN BODY (7) that SEAL (8) is installed. Thread
DRAIN BODY (7) tight against FLANGE (2) to make a water tight seal.
10
9
7
6
12
19
16
15
17
18
2
10
14
13
11
The PIVOT ROD OPENING (9) in DRAIN BODY (7) should face the rear
of the lavatory. Tighten LOCK NUT (6) on FLANGE (2) to make a water
tight connection with channel locks. Do not over tighten.
Teflon Tape
WATER SUPPLY CONNECTIONS
Note:
FLEXIBLE HOSES (1, 2) on FAUCET (3) are (17" Vessel,
22" Lavatory) in length from base of faucet. If longer
supply length is required installer must purchase adapters
and additional supplies to complete connections.
Important: If SUPPLY HOSES (1, 2) are to long, loop as
illustrated to avoid kinking.
Connection on FLEXIBLE HOSES (1, 2) are 3/8" compression.
Connect left supply to (Hot Marked with a Red Tag) and right
supply to Cold wall supply.
Use adjustable wrenches to tighten connections. Do not
over tighten.
1
1A
INSTALL LAVATORY OR VESSEL FAUCET
LAVATORY FAUCET
(814/201)
VESSEL FAUCET
(814/931)
Turn off hot and cold water
supplies before beginning.
CAUTION
With the collar of the EXTENSION (7) facing up slide
the EXTENSION (7) over the
FAUCET SUPPLIES (3)
and
the MOUNTING STUD (
4
). The collar of EXTENSION (7)
fits into the groove of the faucet base. No gasket or
sealant is required.
7
1
3
4
2
Installation with EXTENSION (7)
For single hole mounting only.
Seat O-RING (1) into under side of ESCUTCHEON RING (2).
Feed FAUCET SUPPLIES (3) and MOUNTING STUD (4) through
ESCUTCHEON RING (2) and the mounting hole of lavatory or mounting
surface.
Seat ESCUTCHEON RING (2) with collar facing up into groove in
faucet base.
Seat O-RING (1) into under side of ESCUTCHEON RING (2).
Seat ESCUTCHEON RING (2) with collar facing up into groove in
EXTENSION (7)
base.
From below, push RETAINING WASHER with GASKET (5) onto
MOUNTING STUD (4). Secure Faucet with MOUNTING NUT (6),
pulling faucet to front of sink, so STUD (4) rests against mounting
hole. Before final tightening, adjust Faucet so that it is centered.
Tighten MOUNTING NUT (6) to complete mounting.
For single hole mounting only.
COLLAR
1
2
5
6
4
GROOVE
(FAUCET
BASE)
3
COLD
HOT
SHUT OFF
VALVE
17" Vessel Faucet
22" Lavatory Faucet
3/8" COMPRESSION
RED TAG
RED
RED
1
2
5
6
4
GROOVE
(EXTENSION
BASE)
3
RED
Feed FAUCET SUPPLIES (3) and MOUNTING STUD (4) through ESCUTCHEON RING (2)
and the mounting hole of lavatory or mounting surface.
From below, push RETAINING WASHER with GASKET (5) onto MOUNTING STUD (4).
Secure Faucet with MOUNTING NUT (6), pulling faucet to front of sink, so STUD (4)
rests against mounting hole. Before final tightening, adjust Faucet so that it is
centered. Tighten MOUNTING NUT (6) to complete mounting.
NOTE; FAUCET with EXTENSION (7) is used
for installation with above-counter sinks.
3
4-3/4"
3-5/8"
1" MAX.
1" MAX.
814/201
814/931
4-1/4"
7-1/2"
2" D.
4-3/4"
3-5/8"
9-7/8"
12-3/8"
11-1/8"
2" D.