Jadever 1.5K User Manual Download Page 11

 

 

 

 

4)  Wait  till 

appears,  put  weights

JWL-6K, 2/3 of full load is 4 kg)  

5) Wait till  

  

appears, put weights of full load on the weighing pan (E.g. for JWL

load is 6kg)  

 

6) The calibration procedure ends up with a symbol

7) Remove all the weights, and then press key 

 

  Single Point Calibration 

 

1

 Press and hold key 

M- 

while powering on the scale. The screen displays 

release the  

 

2

 Press key 

TARE 

to enter the zero point

3

 Wait  till  the 

”  appears  (with  the  right

shift leftwards, key 

PRINT/HI 

to shift rightwards, key 

key 

M- 

to decrease setting value.  

4

 Put the corresponding weights on the  weighing pan and press key 

procedure starts. 

5

A few seconds later, the calibration procedure is completed with 

the  screen.  Remove  all  the  weights  and  press  key 

mode. 

7. Setting Mode & Description of Parameter

1) Long press key 

MODE 

for 3 seconds

reverts to available setting items .There

Auxiliary display in the Lower Left corner

2) Press key 

M+ 

or key 

M- 

to step through all the available setting items ,and release on

 

JWL-6K, 1/3 of full load is 2 kg) 

Vetek 

weights  of  2/3  of  full  load  on  the  weighing

 

appears, put weights of full load on the weighing pan (E.g. for JWL

The calibration procedure ends up with a symbol of “ 

Remove all the weights, and then press key 

TARE 

to return to weighing mode.

while powering on the scale. The screen displays 

to enter the zero point calibration 

 

”  appears  (with  the  right-most  digit  blinking),  press  key 

to shift rightwards, key 

M+   

to increase setting values and 

value.  

 

Put  the corresponding weights on  the  weighing  pan and press key 

N/G

the calibration procedure is completed with 

” displayed 

the  screen.  Remove  all  the  weights  and  press  key 

TARE 

to  return  to  normal  weighing  

Setting Mode & Description of Parameter Values 

for 3 seconds

,  

  

display momentarily before the display 

reverts to available setting items .There are 12 available setting items (p00-p11) ,indicated

Auxiliary display in the Lower Left corner .  

 

to step through all the available setting items ,and release on

Vetek Weighing AB 

 

weighing  pan  (E.g.  for 

appears, put weights of full load on the weighing pan (E.g. for JWL-6K,  full 

 

mode. 

while powering on the scale. The screen displays 

”, then 

most  digit  blinking),  press  key 

UNIT/LO 

to 

to increase setting values and 

N/G

, the calibration 

” displayed   on 

to  return  to  normal  weighing  

display momentarily before the  display 

p11) ,indicated by 

to step through all the available setting items ,and release on  the 

Summary of Contents for 1.5K















Reviews: