background image

13

Important:  Read complete instructions before beginning installation.

Each unit arrives ready for installation, equipped with base, glass and associated hardware.
 Remove the unit from the carton.  Retain the shipping carton until satisfactory inspection of the product has been

made.

Immediately upon receipt, inspect the base and other components before installing.  Check all carton inserts for

parts and hardware.  Should inspection reveal any damage or defect in any component, do not install the unit.  Damage
or defect to any component claimed after the unit is installed is excluded from the warranty.  Jacuzzi Whirlpool Bath's
responsibility for shipping damage ceases upon delivery of the products in good order to the carrier.  Refer any claims
for damage to the carrier.  For definitions of warranty coverage and limitations, refer to the published warranty
information packed with the product.

Jacuzzi Whirlpool Bath is not responsible for any defect that could have been discovered, repaired, or avoided by

following this inspection.

BASE SPECIFICATIONS

3 WALL SPECIFICATIONS

DIMENSIONS
60"

(1219 mm) L

42-5/16" ( 1075 mm) W
4"

( 102  mm) H

TOTAL WEIGHT/
FLOOR LOADING
340 lb
(155 kg)/
23 lb/sq. ft.
(97 kg/sq. m)

PRODUCT WEIGHT (Base + Enclosure )
140 lb
(64 kg)

L

W

TOP VIEW

1/2" RIGID
COPPER PIPE
UNDER BASE

1-1/2" TILE FLANGE

FRONT VIEW

1-1/2" TILE FLANGE

H

45

°

 ELBOW

2 PROVIDED

(LOOSE)

NOTE:  MINIMUM WATER PRESSURE
FOR THE SYSTEM IS 40 PSI.

Summary of Contents for SUMMER RAIN

































Reviews: