background image

TOWER PLUMBING REPAIR PARTS

1.   A944000 (9X) Spring Clamp, .625 OD Hose
2.   U405000 L=31.0" Tubing, PVC Reinforced, 10mm Barb
3.   U405000 L=5.5" Tubing, PVC Reinforced, 10mm Barb
4.   A945000 (7X) Spring Clip, .75 OD Hose
5.   U400000 FTG, Straight, 1/2" FTS X 10mm Barb
6.   U403000 (2X) Cap, 1/2" FST
7.   U711000 (2X) Strainer Washer, 1/2" Dia.
8.   U405000 L=31.0" Tubing, PVC Reinforced, 10mm Barb
9.   U540000 (2X) 1/2" Flexhose 38", Female Swivel Heads
10. GASKET (2X) Gaskets Supplied with Hose
11. U827000 (2X) Ball Valve, .5 FTP X .5 MPT L
12. U421000 (11X) Washer, FTG .7 OD
13. U401000 (7X) FTG, Ell, 1/2" FST X 10mm Barb
14. U405000 L=4.5" Tubing, PVC Reinforced, 10mm Barb
15. U404000 (2X) FTG, Y, 10mm X 10mm X 10mm Barb
16. U405000 L=2.5" Tubing, PVC Reinforced, 10mm Barb
17. U402000 FTG, Tee, 1/2" FST X 10mm Barb
18. U405000 L=10.0" Tubing, PVC Reinforced, 10mm Barb
19. U405000 L=4.5" Tubing, PVC Reinforced, 10mm Barb
20. U405000 L=5.5" Tubing, PVC Reinforced, 10mm Barb

1 (9X)
See Note 1

2

3

5

6

20

8

(2X)

12 (11X)

13 (7X)

14

15 (2X)

16

17

18

19

4 (7X)
See Note 2

7

10 (2X)

11

Note 1:  For Clamping U405000 to U401000 or U402000.
Note 2:  For Clmping U405000 to U400000 or U404000.

26

Summary of Contents for SUMMER RAIN

































Reviews: