background image

5

8.

Installer must determine the best way to drill holes in the countertop, ensuring

proper alignment with the sink without damaging the finished countertop surface.

9.

Install the faucet according to the faucet installation instructions, inserting the

faucet through the faucet holes in the sink and the countertop.  The faucet holes in the
sink have been enlarged to allow the faucet to be raised through the countertop.
When the faucet is securely in place, attach the new hot and cold water supply tubes
to the faucet tubes.

10. Connect the drain tailpiece to the bot-
tom of the pop-up, then fasten the trap and
drain extension to the wall stub-out in the
wall. See Figure 4. You may use metal or
plastic drain pipe and trap, following the
directions provided by the manufacturer.

11. Use a tube cutter to trim the free ends
of the hot and cold supply tubes to at least 1/
4" longer than necessary to reach into the
inlets of the shut-off valves. It is better to cut
the tubes longer than needed, then trim
them again. Remove any burrs or sharp
edges with an emery cloth.

The supply stop handles cannot extend
more than 3" (7.6 cm) from the finished wall when in the open position.

Join the hot and cold water supplies to the shut-off valves as instructed by the faucet
manufacturer.

12. Turn on the main water supply then open the shut-off valves. Check all connections
for leaks. A slight tightening of about 1/4 turn will normally stop any leaks.

LOCKNUT

COMPRESSION RING

SLIP NUT

SLIP NUT
WASHER

P TRAP

CLEAN OUT PLUG

SINK

Figure 4

STRAINER BODY

PLUMBERS PUTTY

Summary of Contents for BM43000









Reviews: