background image

3 SAFETY

en-7

3.1.3 OPERATION

 a

Never  operate  the  engine  without  enough  ventilation  or  in  an  enclosed  area.  The  carbon  monoxide  in  the

exhaust fumes can increase to dangerous levels.

 b

Never carry passengers. Keep bystanders or animals away from the mower.

 c

Disengage all drives and engage the parking brake before you start the engine. Only start the engine with the

operator in the seat. Never start the engine with anyone standing near the mower.

 d

Keep your legs, arms and body inside the operator compartment while the mower is in operation. Keep your

hands and feet away from the cutting units.

 e

Do not use on the slopes greater than the safe slope limit for the equipment.

 f

To guard against over turning or loss of control:

 –

Operate the mower up and down on the face of slopes (vertically), but not across the face (horizontally).

 –

Do not start or stop suddenly on slopes.

 –

Decrease  the  speed  when  you  operate  on  slopes  or  when  you  must  turn.  Use  caution  when  you  change

direction. Turf condition can change the mower stability.

 –

Use caution when you operate the mower near drop-offs, ditches or embankments.

 –

Be careful of holes in the terrain and other hazards that are not visible.

 g

When you drive in the reverse direction, look behind you and down to make sure the path is clear. Do not operate

the cutting units when you drive in the reverse direction.

 h

Use caution when you go near corners, trees or other objects that can prevent a clear view.

 i

Equipment must meet the current regulations to be driven on the public roads.

 j

Before you move across or operate on the paths or roads, turn off the PTO switch, lift the mowers and travel at

decreased speed. Look for traffic.

 k

Stop the blades when the mower is on any surface that is not grass.

 l

Do not release the cut grass in the direction of bystanders

 

or allow bystanders near the mower while in operation.

 m

Do not operate the mower with damaged guards or without safety devices in position.

 n

Do not change the engine governor setting or over-speed the engine. Never change or tamper with adjusters that

are closed with a seal for the engine speed control.

 o

Before you leave the operator compartment, for any reason:

 –

Disengage all the drives and lower attachments to the ground.

 –

Engage the parking brake.

 –

Stop the engine and remove the key.

 p

When you hit an object or mower starts to cause the vibration that is not normal, inspect the mower for damage

and make repairs.

 q

Decrease the throttle setting before you stop the engine.

 r

Do not use this equipment for uses that the mower was not made for.

Summary of Contents for LF557





























































































Reviews: