background image

GENSET AND BATTERY PACK

4271491-Second Edition

3-39

3

Assembly Notes

• Apply Loctite

®

 242 (Blue) to screw (36) prior to 

assembly.

• Apply Loctite

®

 242 (Blue) to two screws (25) prior to 

assembly.

• Apply Loctite

®

 242 (Blue) to four mounting flange 

screws (6) prior to assembly.

• Tighten four mounting flange screws (6) to 32 lb-ft 

(43.4 N·m).

• Apply Loctite

®

 242 (Blue) to four generator assembly 

mounting screws (22) prior to assembly.

• Tighten four generator assembly mounting screws 

(22) to 20 lb-ft (27.1 N·m).

• Apply Loctite

®

 242 (Blue) to eight isolation mount 

screws (35) prior to assembly.

• Apply Loctite

®

 242 (Blue) to four engine mounting 

screws (28) prior to assembly.

• Tighten four engine mounting screws (28) to 19 lb-ft 

(25.5 N·m).

• Apply Loctite

®

 242 (Blue) to four engine plate screws 

(27) prior to assembly.

• Install key (9) flush with face of crankshaft.

• Install engine coupler (17) flush with face of 

crankshaft.

• Apply Loctite

®

 242 (Blue) to engine coupling screw 

(16) prior to assembly.

• Tighten engine coupler screw (16) to 32 lb-ft 

(43.4 N·m).

Engine Service (Gasoline Models)

A separate engine manual, prepared by the engine 
manufacturer, is supplied with this machine. Refer to the 
engine manufacturer’s manual for all engine-related 
service.

Proper attention to the engine manufacturer’s manual 
directions will ensure maximum service life of the engine.

Repair—Batteries

Battery Pack, Battery Pack Tray, and 
Battery Filling System

Removal and Installation

See Figures 3-65 through 3-69.

WARNING

WARNING

1.

Park the mower safely. (See “Park Mower Safely” on 
page 1-6.)

2.

Raise the hood.

Figure 3-65

NOTE

Direction of arrow indicates front of machine.

3.

Disconnect four filling hoses (6) from the four upper 
8-volt batteries (3).

Required Materials

Loctite

®

 242 (Blue)

Be sure that the key switch is off, all electrical 
accessories are turned off, and the 48-volt power 
connector is disconnected before starting work 
on machine.

• Battery posts, terminals, and related 

accessories contain lead and lead 
compounds. Wash your hands after handling.

• Always wear eye protection when servicing 

battery.

TN2802

1

11

10

4

7

3

2

5

8

9

6

Summary of Contents for Eclipse 322 62800



















































































Reviews: