JACLO J-TH34 Installation Instructions Manual Download Page 15

OCTOBER 3, 2017

jaclo

 

industries 

 |  129 Dermody Street   Cranford, NJ 07016

p

 908.653.4433 | 800.852.3906   

f

 908.653.1717 | 800.852.4133   

JACLO.COM

   |   PG 15

Over Fifty Years of Excellence 

Proud to be an American Company

CARE INSTRUCTIONS

WARRANTY

In order to maintain the high quality finish of JACLO products, please 

adhere to the following product care instructions:

Cleaning JACLO products:

  For routine cleaning, simply use a soft 

damp cloth and common household soap, then rinse and dry.  

 

Proper care of your product is important because most water 

contains calcium that deposits on surfaces, forming unpleasant spots.  

This can be avoided by routine cleaning and drying after every use.  

Use only mild soap detergents.  JACLO products may be periodically 

waxed with non abrasive compounds, such as Flitz

®

 faucet wax.

Residential Warranty:

  Your new plumbing fixture is warrantied by 

JACLO INDUSTRIES

, 129 Dermody Street, Cranford, NJ 07016.  

This warranty is extended to original consumer purchasers only.  

This warranty gives you specific legal rights, and you may also have 

other rights which vary from state to state.

The product (including the finish on the product but excluding any 

custom finishes and any installation hardware not supplied by 

JACLO) is warranted to be free from defects in material or 

workmanship under normal use and service for the lifetime* of the 

fixture, so long as the original consumer purchaser owns it.  

JACLO's sole obligation under this or any other warranty is limited 

to repairing or replacing at JACLO's option, without labor, any part 

or parts of the fixture which fail to conform to such warranty.

JACLO WILL NOT BE LIABLE FOR ANY CONSEQUENTIAL OR 

INCIDENTAL DAMAGES CAUSED BY A BREACH OF THIS OR 

ANY OTHER WARRANTY.

Some states do not allow the exclusion of limitation of incidental or 

consequential damages, so the above limitation may not apply to 

you.

To secure warranty performance, the original consumer purchaser 

must have the fixture properly and professionally installed in 

accordance with all codes and installation instructions.

Items and actions that will void the JACLO warranty are:

• 

Abuse, misuse, neglect and accidental damage

• 

Improper cleaning, care and maintenance of the fixture

• 

Alteration of the fixture in any way including removal of a flow 

regulator/restrictor

All warranty claims must be made in accordance with the JACLO 

return policy (see below).

JACLO does not authorize any distributor, retailer or other person 

to modify this warranty or assume any liability on its behalf with 

respect to it.  Any question regarding the operation of warranty 

should be addressed to JACLO's warranty department.

*Due to the unpredictable environment, all kitchen drains, strainers 

and garbage disposal flanges are warrantied for the period of one 

year from date of purchase from an authorized JACLO dealer.  

 

Un-lacquered Brass (ULB) is a living finish and is excluded from any 

finish warranty.

Commercial Warranty:

  JACLO offers the above warranty for a 

 

period of one year from date of purchase to purchasers of products 

for industrial, commercial, business and all non-private residential 

uses.

Never use abrasive cleaners, bleach, disinfectants or cleaning 

products containing alcohol, ammonia, hydrochloric or phosphoric 

acids as they will damage the product finish.

Please note:

  Your product warranty may not be valid if the above 

cleaning guidelines are not followed.

Summary of Contents for J-TH34

















Reviews: