7
ENTERING THE ADVANCED INSTALLER SETTINGS MENU
ENTERING THE ADVANCED INSTALLER SETTINGS MENU
The T-32-P contains factory defaults for all Advanced
Installer Settings. Depending upon the user and
equipment application, some settings may need to be
changed.
To enter the Advanced Installer Settings menu, push the
button once then hold it down (15 seconds) until
the number “
” is displayed on the LCD. Using the
( ) ( ) arrow button, adjust the value until it reads
“
” and then press the
button to enter the
menu. You can move forward or backwards through the
menu by pressing the
or
buttons.
O/RIDE
88:15
88:32
O/RIDE
O/RIDE
PROG
ADVANCED INSTALLER SETTINGS MENU
MODE
MODE
FAN
PROG
MODE
Manual Mode
LC=00 - Keyboard lock OFF.
(Sw6=OFF)
LC=01 - All buttons are locked except
button.
LC=02 - All buttons are locked except
and ( ) ( ) buttons.
LC=03 -
, and
are locked.
button can only select Auto or
OFF.
LC-04 -
MODE
button can only select
Auto or OFF.
LC-05 - All buttons are locked.
LC-06 - Same function as LC-05.
HL
90
Maximum Heating or High Temperature
Limit.(Adjustable from 41° F - 120° F)
CL
50
Minimum Cooling or Low Temperature
Limit. (Adjustable from 43° F - 122° F)
CF
F
Temperature Display
(Degrees F or C)
C1
0.0
Internal Sensor Calibration
(Adju/- 9° F)
HL
CL
CF
CI
ADVANCED INSTALLER SETTINGS MENU
FO=2 - In programmable mode
(Sw6=ON), fan runs continuously with
program 1 through 4 and then in AUTO
from program 4 - 1.
FO=3 - In programmable mode
(Sw6=ON), fan control is a combination
of option 1 and 2.
FP
0
Fan Purge
Adjustable from 0 - 5 minutes after
heating or cooling cycle.
FN
A
Mode - Heat / Cool system.
FN=C - Cooling only system.
FN=H - Heating only system.
H3
AL
FP
88
H3
H3=AL - W2 relay used for auxiliary and
emergency heat.
(Sw1 = OFF) (Sw2 = ON)
NO
OR
BOTH
TT
RS
For
remote sensor
1 or more
remote indoor sensor without the
onboard sensor being used.
TT=OA - For outdoor remote sensor
connection.
TT=DA - Sends measured temperature
from remote sensor via modbus but
does not display the value on the LCD.
TT=OC - For connecting dry contact
switch.
(Replaces user setpoints with
pre-programmed cooling ‘OC’ and
heating ‘OH’ setpoints)
TT=OF - For connecting dry contact
switch.
(Turns thermostat off when closed)
TT=AV - For averaging
the
internal thermostat sensor and remote
indoor sensor(s) together.
AF
1
Freeze protection ON. If thermostat is
OFF, heating will come on if room
temperature falls below 41° F.
AF=0 - No freeze protection.
OH
OF
Override Heating Setpoint.
(Adjustable from 41° F - 120° F)
OC
OF
Override Cooling Setpoint.
(Adjustable from 43° F - 122° F)
88
AF
8H
8C
ST
OF Leave at factory default
SC
OF
Leave at factory default
S8
SC
Symbol Default Function
4 Schedules
Temporary Program Override 0 (OFF)
(Sw6=ON)
extends override to next program
(Sw8=ON)
change. 1 - 12 equals fixed hours of
override.
AH
2.0
After Hours Override Timer
AH
TD=0 - Displays set and space
temperatures.
TD=1 - Displays only the set
temperature.
TD
0
Temperature Display
88
TC
12
Time Format
(12 or 24 Hour Clock)
8C
Symbol Default Function
O/RIDE
MODE, O/RIDE
MODE
O/RIDE
PN
32
Keyboard Lock PIN. This is the required
PIN for future entry into the Advanced
Installer Setup menu. (Range 00-99)
LC
00
Keyboard Lock OFF
Programmable Mode
LC=01 - All buttons are locked except
( ) ( ) buttons.
LC=02 - All buttons are locked except
and( ) ( ) buttons.
LC=03 - All buttons are locked except
and ( ) ( ) buttons.
LC=04 - All buttons are locked except
and ( ) ( ) buttons.
LC=05 - All buttons are locked except
button.
LC=06 - All buttons are locked.
88
LC
H3=EH - W2 relay controls emergency
heat.
H3=AH - Do not use this function.
H3=FF - Fossil Fuel (Y is locked out
when W2 is energized.
H3 = OF - W2 relay only operates as
auxiliary heat in heat pump mode.
