jablotron JA-65X Installation Manual Download Page 7

Digital communicator JA-65X 

7/7 

MFM53103 

 

6  Remote access to the system 

 

The JA-60U modem can be used for the remote connection of 

the control panel to a personal computer with Comlink software or 

a remote JA-60E keypad using a standard telephone line. It is 

necessary to know the remote control access code for the system 

(see 3.2). 

Details on how to use the JA-60E keypad remotely can be 

found in the JA-60E manual. 

A personal computer connected remotely works the same way 

as when it is wired directly to the control panel (see also 

installation manual of the control panel). Only downloading or 

uploading of extensive data (like event list downloading, digital 

communicator setting etc.) takes a slightly longer time compared 

to a direct PC connection to the control panel. 

 

6.1 

Establishing connection with a remote control 

panel by computer 

 

Start Comlink SW on a computer equipped with a JA-60U 

modem. The dialing dialog requires the following data: 

  telephone number of the called control panel 

  dialing method (tone or pulse) 

  control panel’s remote access code (must be identical 

as code programmed in the control panel - 8 digits) 

  optional bypassing of answering machine (if this 

option was programmed in the control panel); if the 

connection can not be established, try to enter 

“space” after the last digit 

  optional call back feature, if you want the control 

panel to call your computer back (that way the end 

user’s telephone will be charged for the remote 

access communication)

 

 

“Dialing in” dialog of the Comlink software 

7  Specification

 

 

Digital communication to: 

  a monitoring station,  

  5 SMS messages or Pager dialing,  

  2 voice messages, modem communication with a remote 

PC (ComLink SW + JA-60U modem),  

  remote keypad access with JA-60E and JA-60U 

 

Monitoring station formats  

Contact ID, Ademco, Telemax, Franklin, Radionics, SurGard, 

DTMF2300, (198 reports codes) 

 

can be connected to analogue interfaces TBR 21/1998, EG 

201 121 V1.13/2000, AS/ACIF S002/2001 (Australia) 

 

JABLOTRON ALARMS a.s. hereby declares that 

the JA-65X is in a compliance with the relevant 

Union harmonisation legislation: Directives No: 

2014/35/EU, 2014/30/EU, 2011/65/EU. The original 

of the conformity assessment can be found at www.jablotron.com 

- Section Downloads. 

 
Note:

  Although this product does not contain any harmful 

materials we suggest you to return the product to the dealer or 

directly to the producer after usage. 

 

 

 

Summary of Contents for JA-65X








Reviews: