background image

 

July 13, 2017 

 

 

12 

Mobile home installation 

DANGER DO NOT INSTALL IN BEDROOM. 
WARNING THE STRUCTURAL INTEGRITY OF THE MOBILE 

HOME  FLOOR,  WALL,  AND  CEILING/ROOF  MUST  BE 
MAINTAINED. 
VAPOR  BARRIER  EFFICACITY  AROUND  THE  CHIMNEY 
AND  FRESH  AIR  INTAKE  MUST  BE  KEPT  IN  GOOD 
CONDITION.  

1)  Follow the «General stove installation» (p.10) from steps 

1 to 10. 

2)  The following requirements are MANDATORY for 

mobile home installation. 

a.  The stove must be fixed permanently on the mobile 

home’s floor with bolts and nuts.  

b.  The exterior air intake must be installed.  
c.  The stove must be electrically-grounded to the mobile 

home’s chassis. In the USA, electrical grounding with   

8 gauge wire using star washers and certified 
terminals is mandatory. 

d.  All of the following equipment must be certified and 

approved for mobile home installation. 

 Double wall chimney pipe; 

 The chimney system; 

 The roof flashing; 

 The Storm collar; 

 Chimney cap with fire screen; 

 Firewall; 

 Chimney ceiling support; 

 Decorative collar.

 

 

e.  If  the  chimney  is  exposed  outside  from  a  wall  and 

placed lower than 7 feet (213 cm) above the ground 

level  where  the  mobile  home  is  situated,  a  guard 

must be installed around the chimney at the height 

of    7  feet  (213  cm).  If  openings  are  made  in  the 
guard,  they  must  be  less  than  ¾  inch  (19.5 mm) 

wide. guard openings must be kept at least 4 inches 

(10.2 cm) away from the chimney surface in order to 
avoid contact. 

f. 

The chimney must exceed of at least 3 feet (91.4 cm) 

the highest point of the opening made in the roof and 

it must also exceed of 2 feet the highest point of the 
roof inside a 10 feet distance from the chimney. 

g.  Be sure to seal correctly the flashing of the roof, the 

firewall and the exterior air intake with sealant. You 
should also pay attention to the efficacy of the vapor 
barrier is not compromised.  

3)  Always keep the door closed. Open it only when adding 

wood or when starting a fire. 

4)  To close the exterior air intake when the stove is not in 

use, a damper must be installed in the air intake pipe. 

5)  Don’t forget to open the damper when you operate your 

stove so that smoke will not fill the house. 

6)  Always use certified parts for mobile home. Never use a 

substitute for replacement. 

Summary of Contents for Elda




































Reviews: