background image

Hose Strainer Depth Setting

The hose strainer depth is either set by a buoyant 

float inside the strainer or chained up at a specific 

depth.  If the hose strainer is not tied up using 

the attached chain, the water will enter the hose 
approximately 1.5 to 2 feet (0.45m to 0.6m) above 
solid bottom of the pond.  In some cases, the hose 
strainer depth will need to be chained up to a 
higher level in the water.

Hose Strainer Depth Adjustment
TOOLS RECOMMENDED:

Tape Measure

STEP 1:

 Determine the new hose strainer setting 

after consulting with a Ixom Watercare, Inc. 
service team member.

STEP 2:

 Use the tape measure to determine how 

deep the pond at the Mixer.

STEP 3:

 Locate the white float ball that is on one 

of the floats.  This float ball marks the chain that is 
attached to the submerged hose strainer.

STEP 4:

 If the strainer is suspended by the 

buoyant float and not tied up by the chain, the 
strainer is approximately 1.5 to 2 feet (0.45m 
to 0.6m) above the solid bottom.  If the strainer 
is tied up, let it loose so it is suspended by the 
buoyant float.  Use the depth measurement made 
in Step 2 to determing how deep the strainer is.

STEP 5:

 Lift the chain up until the strainer is at the 

desired setting and tie off to the float plate.

Strainer Free Floating, Not Tied Up

White Float Ball

Strainer Chained Up, Not Free Floating

Pond Depth

1.5 to 2.0 

feet

(0.45m to 

0.6m)

©2022 IXOM Watercare Inc. | www.ixomwatercare.com | 866 - 437 - 8076 | [email protected]

Maintenance

Hose Strainer Depth and Cleaning

SB / GF Series Mixers

2059_10262_20220110

O&M_GF2500_10115_20220121 - 27

Summary of Contents for GridBee GF2500
















































Reviews: