IVT SNWB-163, Operating/Safety Instructions Manual

Page: 6 / 52

6
Manual instruction | Snow blower
EN
the engine
Never store the machine or fuel container •
inside where there is an open flame, spark or
pilot light (e.g furnace, water, heater, space
heater ,clothes dryer etc.)
Allow machine to cool at least 5minutes •
before storing.
Operation
Do not put hands or feet near rotating parts, •
in the auger/impeller housing or chute assembly
.Contact with the rotating parts can amputate
hands and feet.
The auger/impeller control is a safety device •
.Never bypass its operation .Doing so makes the
machine unsafe and may cause personal injury.
The controls must operate easily in both •
directions and automatically return to the
disengaged position when released.
Never operate with a missing or damaged chute •
assembly. Keep all safety devices in place and
working.
Never run an engine indoors or in a poorly •
ventilated area. Engine exhaust contains carbon
monoxide, an odorless and deadly gas.
Do not operate machine while under the •
influence of alcohol or drugs.
Muffler and engine become hot and can cause a •
burn. Do not touch.
Exercise extreme caution when operating on or •
crossing gravel surface. Stay alert for hidden hazards
or traffic.
Exercise caution when changing direction and •
while operating on slopes.
Plan your snow-throwing pattern to avoid •
discharge towards windows, walls, cars etc. Thus
avoiding possible property damage or personal
injuiry caused by a ricochet.
Never direct discharge at children, bystanders •
and pets or allow anyone in front of the machine.
Do not overload machine capacity by attempting •
to clear snow at too fast of a rate.
Never operate this machine without good •
visibility or light. Always be sure of your footing and
keep a firm hold on the handles. Walk, never run.
Disengage power to the auger/impeller when •
transporting or not in use.
Never operate machine at high transport speeds •
on slipper surface. Look down and behind and use
care when in reverse.
If the machine should start to vibrate abnormally, •
stop the engine, disconnect the spark plug wire and
ground it against the engine. Inspect thoroughly for
damage.
Disengage all controls and stop engine before •
you leave the operating position (behind the
handles). Wait until the auger/impeller comes
to a complete stop before unclogging the chute
assembly, making any adjustments or inspections.
Never put your hand in the discharge or collector •
openings. Always use the clean-out tool provided to
unclog the discharge opening. Do not unclog chute
assembly while engine is running. Shut off engine
and remain behind handles until all moving parts
have stopped before unclogging.
Use only attachments and accessories approved •
by the manufacturer (e.g. wheel weights, tire chains,
cabs etc.).
If situations occur which are not covered in this •
manual, use care and good judgment. Contact the
distributors where you bought the snow thrower or
your nearest servicing dealer
Maintenance and storage
Never tamper with safety devices. Check their •
proper operation regularly. Refer to the maintenance
and adjustment sections of this manual.
Before cleaning, repairing or inspecting machine •
disengage all controls and stop engine. Wait until
the auger/impeller come to a complete stop.
Disconnect the spark wire and ground against the
engine to prevent unintended starting.
Check bolts and screws for proper tightness •
at frequent intervals to keep the machine in safe
working condition. Also, visually inspect machine
for any damage.
Do not change the engine governor setting or •
over-speed the engine. The governor controls the
maximum safe operating speed of the engine.
Snow thrower shave plates and skid shoes •
are subject to wear and damage. For your safety
protection, frequently check all components and
replace with original equipment manufacturer’s
(OEM) parts only. “Use of parts which do not meet
the original equipment specifications may lead to
improper performance and compromise safety!”
Check clutch controls periodically to verify •
they engage and disengage properly and adjust. if
necessary, Refer to the adjustment section in the
operator’s manual for instructions.
Maintain or replace safety and instruction labels, •
as necessary.
Observe proper disposal laws and regulations •
for gas, oil, etc. to protect the environment.
Prior to storing, run machine a few minutes to •
clear snow from machine and prevent freeze up of
auger/impeller.
Never store the machine or fuel container inside •
where there is an open flame, spark or pilot light
such as a water heater, furnace, clothes dryer etc.