![background image](http://html.mh-extra.com/html/ivt/ld-500/ld-500_manual-instruction_2097763009.webp)
9
Manual instruction
EN
• Never operate the tool with defective safety
devices or guards (if present), or without safety
devices in place .
• Inspect the entire tool to look for loose parts
(e.g. nuts, bolts, screws, etc.) and for any damage.
Check at frequent intervals if screws and bolts
are properly tight to be sure the equipment is in
safe working condition. Repair or replace them, if
necessary, before using the tool. Serious injury to
the operator and to the bystanders could result if
there’s a damage to the tool .
• While using the tool, dress properly. Do not
wear loose clothing or jewelry that could become
caught by the tool. Wear suitable working clothes.
It is recommended that legs and feet are covered, to
protect from flying debris. Long air should be tided
back.
• Keep handles and grips dry, clean and free from
oil and grease.
• Use a proper protective equipment. Use safety
glasses and safety gloves. Also use a dust mask
during pulverulent operations or if exaust gases
are present. When necessary, use also non-slipping
boots or shoes, hardhat and earplugs. If the noise
level exceeds 85 dB(A), ear protection is obligatory.
WARNING! Use personal protective
equipment! Safety devices and the
personal protective equipment protect
your own health and the health of others and
ensure a trouble-free operation of the tool .
• Do not start to use the tool if it is in an inverted
position or it is not in the right working order.
• Ensure that you have a good stand, while you
operate with the tool. Keep proper footing and
balance at all times.
• Keep work area clean. Cluttered areas invite
injuries. Before use, all foreign bodies must be
removed from the working area, also pay attention
to foreign objects during the operation.
• Do not force the tool.
• Only work in daylight or sufficiently good
artificial light. Never operate the tool without good
visibility.
• Be careful not to drop the tool or hit it against
obstacles.
Stay alert. Watch what you are doing.
Distraction can cause you to lose
control. Use common sense.
Electrical safety rules
ATTENTION! When using electrical tools,
the following safety instructions should be
observed to prevent the risk of electric shock,
personal injury and fire. Read and observe these
instructions carefully before using the tool.
• It is recommended for increased electrical
safety to use a Residual Current Device (RCD) with
a tripping current of not more than 30 mA. Always
check your RCD every time you use it. Consult a
reliable electrician.
WARNING! The use of an RCD or other
circuit breaker unit does not release the
operator from the safety instructions
and safe working practices given in this manual.
• The main voltage must correspond to the one
marked on the technical data plate. Do not use
other sources of power.
• Before inserting the plug in the main socket,
make sure that the socket ratings are correct and
correspond to those indicated on the rating label on
the appliance.
• Avoid body contact with grounded surfaces
such as pipes, radiators, ranges and refrigerators.
This increases risk of electric shock if your body is
grounded.
CAUTION: touching electrified parts
may cause death by electric shock or
burn.
• Never move the appliance by pulling at the cables.
• Do not abuse the cord. Keep it away from heat,
oil, sharp edges or moving parts.
• Always guide the connection line safely.
• Do not use power tools near flammable liquids
or gases.
• Always disconnect the appliance from the mains
supply before transporting it to other places.
CAUTION: The appliance should always
be switched off at the mains before
disconnecting any plug and socket
connector or extension cables.
• Never pass the appliance over the extension
cable while the tool is working. Make sure you
always know where the cable is.
• Do not wire an extension cable directly into your
device yourself. Instead, take the device to your
nearest authorized Service Centre.
ATTENTION! DANGER OF ELECTRIC SHOCK!
Consider working area environment. Do not expose
Summary of Contents for LD-500
