17
Instruction manual
EN
the front.
Plunge sawing
ATTENTION
Only soft materials such as wood, aerate concrete, plaster
board, etc may be worked with the plunge method.
Cut-outs in wood are possible without predrilling by piercing
with the running machine. This requires certain amount of
practice, however, and is possible only with short saw blades.
Place the front edge of the base plate on the workpiece and
•
switch on.
Press the machine firmly against the workpiece and plunge
•
the saw blade slowly into the workpiece.
After reaching the required cutting depth, bring the
•
machine again to the normal working position so that the
complete surface of the base plate rests on the workpiece and
continue to saw along the cutting line. [F6]
After completing the cut, first switch «off» the machine an
•
then pull it out of the cut.
Circle cutting (circle cutting guide not included)
[F7]
Mark the circle which will be cut and drill the opening in
•
its centre.
If the cutting does not start from the edge of the material,
•
drill the opening from which the cutting will start.
Mount the circular guide on the machine.
•
Slide the circular guide in order to determine the radius of
•
cutting and lock it using the locking screws (11).
Place the aligning pin in the central opening and start the
•
cutting by moving the device over the circle.
In order to get the optimal results it is recommended to use
the narrow blades.
Maintenance and storage
CAUTION
Before any work on the machine itself, pull the mains plug.
Always keep the tool and the ventilation slots (if present)
•
cleaned. Regular cleaning and maintenance of the appliance
will ensure efficiency and prolong the life of your tool.
If the tool should fail despite the rigorous manufacturing
•
and testing procedures, the repair should be carried out by an
authorized IVT customer service.
Keep all nuts, bolts, and screws tight, to be sure the tool is in
•
safe working condition.
Replace worn or damaged parts for safety.
•
Use only original spare parts. Parts not produced by
•
manufacturer may cause poor fit and possible injury.
Store the tool in a dry room out of reach of kids and away
•
from any flammable material.
Never wet the device or spray water on it!
•
Use a damp cloth to clean the plastic elements. Do not use
•
any cleansers, solvents, or pointed objects.
Regularly clean any dust that is stuck to the ventilation slots
•
(9) and moving parts with a soft brush or a paint brush.
Oil the saw blade guide roller (6) regularly.
•
Environmental protection
Recycle raw materials instead of disposing as
waste.
Tool, accessories and packaging should be sorted for
environment-friendly recycling.
The plastic components are labelled for categorized recycling.
These instructions are printed on recycled paper manufactured
without chlorine.
Summary of Contents for JS-400SG
