ivo isiLine ISI30 Series, Operating Instructions Manual

Page: 7 / 16

7
english
Main technical features:
Display: LCD, 8 decades, height of the figures 8 mm.
Display range:
-9999999 ... 99999999
with leading zeros suppression.
Overflow: In case of a display range overflow, the
counter starts again from 0, but without
removing the leading zeros and activating
all decimal points.
In case of a display range underflow, the
counter starts again from 0 and displays the
minus sign, without removing the leading
zeros and activating all decimal points.
Keys: Electrical locking of the reset key
Housing: Panel mounting, 48 x 24 mm
according to DIN 43 700, RAL 7021
Panel cut-out:
22,2
+0,3
x 45
+0,6
mm
Mounting depth: approximately 48 mm
Weight: approximately 50 g
Protection level: IP65 on the front side
Connection:
Screw terminals, RM 5.00, 8 poles
Rated cross-section: 4,0 mm
2 single-wire
2,5 mm 2 thin wire
AWG 12
Connection diameter:
0,4 ... 2,3 mm single-wire
AWG 28-12
EMC: Interference emissions EN55011 Class B
Interference resistance EN 61000-6-2
Low Voltage Directive (for the AC models):
EN 61010 Part 1 ; overvoltage category 2,
contamination level 2
Power supply:
Non-replaceable lithium battery
(lifetime approximately, 8 years at 20°C)
Working temperature:
–10 ... +55 °C, relative humidity < 85%,
without condensation
Operating temperature:
–10 ... +60 °C
Storage temperature:
–20 ... +70°C
Backlighting:
external electrical source
(24 V DC ±20 %, 50 mA)
Screw terminals 1 and 2:
Function and max. frequences(Pulse/Pause 1:1)
see Table 2
NPN : active for negative edge
Input resistance: approximately 1 MOhm
Low level: 0 ... 0,7 V DC
High level: 3 ... 30 V DC
PNP : active for positive edge
Input resistance: approximately. 100 kOhm
Low level: 0 .. 0,7 V DC
High level: 4 .. 30 V DC
Table 2
Input specification, pin assignment and adjustable operating modes (DC versions).
A control input (screw terminal 5) allows adjusting the operating mode.
Screw terminal Nr. 1 Nr. 2 Nr. 3 Nr. 4 Nr. 5 Nr. 6 Nr. 7
not active
=
adding
contact with
GND =
subtracting
ISI30.010AX01
ISI30.012AX01
ISI31.010AX01
ISI31.011AX01
ISI33.010AX01
ISI33.011AX01
0 7 kHz
12 kHz
0 7 kHz
12 kHz
0 3 kHz
0 6 kHz
NPN
NPN
PNP
NPN
PNP
30 Hz NPN
NPN
0 7 kHz
12 kHz
0 3 kHz
0 6 kHz
NPN
PNP
NPN
PNP
NPN reset input
NPN reset key locking input, Cont
act with GND, key free..
not active
=
Cnt.Dr Mode
contact with
GND =
Up.Dn Mode
not active
=
Quad Mode
contact with
GND =
Quad2 Mode
GND = 0 V DC
Backlighting (–)
Designation
Model
INP A INP B Reset Reset
Enable
Control inputs for operating
mode (Mode)
GND BL
–
Nr. 8
BL
+
Backlighting (+)
PNP