Iveco Motors N45 MNA M10.00 Use And Maintenance Download Page 22

21

ENG

L

ISH

I) Maximum period when using good quality fuel, (EN 590 standard);

this is reduced if the fuel is contaminated and alarms are triggered
due to blockage of the filters and presence of water in the pre-filter.
When blockage of the filter is indicated, it must be replaced. If the
water in pre-filter indicator does not go out after drainage, the pre-
filter must be replaced

2) The frequency with which operations are carried out will depend

on the working conditions and efficiency/wear of the product. If the
engine is not used for long periods of time, check it before you start
it.

3) Refers to engines with traditional and automatic tensioning devices.
4) The anode must be replaced if corrosion has exceeded 50% of the

volume of zinc.

5) Replace lubricants according to the frequency indicated in the

REFUELLING table.

6) Sea water/combustion air heat exchanger: clean both the air and

water sections; engine coolant/sea water heat exchanger: clean the
sea water section; optional sea water/marine gear oil heat
exchanger: clean the sea water section.

7) Must be performed annually, even if the required number of

working hours are not reached.

8) Only use filters with the following characteristics:

- filtration level < 12 µm
- filtering efficiency ß > 200.

Special maintenance

Frequency

Check wear in sea water pump rotor

900 hours 

Change auxiliary member belt

1200 hours or 2 
years

Clean heat exchangers

2 years 

(6) 

Clean the turbocharger

2 years

 (5) 

Injector calibration

1800 hours

Overhaul injection pump

3000 hours

Adjust play in valves-rocker arms

3000 hours

WARNING

When using fuel with a percentage sulphur exceeding 0.5%, or when
using oils that do not comply with the specifications provided in the
refuelling table, the times at which the engine oil, engine oil filter and
oil vapour filter must be changed will vary according to the use and
working conditions of the engine itself; for further information, please
consult the technicians responsible for maintenance.

Summary of Contents for N45 MNA M10.00





































Reviews: