background image

3

PINNER APPLICATORS

5200647 Rev G

1. SAFETY

NOTE

 – Statements identified with a NOTE indicate precautions necessary 

to avoid potential equipment failure.

CAUTION

 – Statements identified with a CAUTION indicate potential  

safety hazards.

The following safety procedures must be followed for safe Pinner operation.
1.  Read instruction manual before operating or installing device.
2.  Qualified service personnel must do installation and repairs.
3.  Turn off power supply before cleaning, adjusting or servicing the Pinner 

applicator.

4.  Do not install or operate Pinner applicators close to flammable materials, 

solvents or gases.  These materials may ignite.

5.  Do not touch the head of the Pinner applicator during operation.
6.  All metal parts near the Pinner applicator, including the frame of which it is 

mounted, must be electronically grounded or shock may result.

7.  Provide proper grounding for the power supply (refer to power supply 

instruction manual) and the flex arm, if used.

2. INTRODUCTION

Simco-Ion’s  Pinner Series static charge applicators consists of the Linear Pinner, 

5-Point and Pinner Claw.  Pinner applicators are arc-resistant to avoid suspension 

of static charge and loss of pinning action. The Pinners are current limited to ensure 

operator and equipment safety.
Arcing can cause a multitude of problems such as EMI interference, shutdown 

of production lines and personnel injury due to surprise from electrical shock.  

Resistance to arcing means that the Pinner applicators continuously supply static 

charge.  This feature makes them easier and safer to set up and use. The Pinner 

also produces superior bonding compared to less sophisticated applicators.  The 

applicators are also available in a non-current limited version for less sensitive areas.

Features and Benefits

•  Current limited design for operator and equipment protection
•  Arc condition sensing and instantaneous intervention resulting in uninterrupted 

pinning action

•  Minimized EMI and RFI generation, preventing disruption of sensitive 

controls

•  Optional manual adjust gooseneck with easy lock/release feature and insulative 

brackets

Summary of Contents for Simco-Ion Pinner Series











Reviews: