background image

Thank you for buying Simco-Ion products. This equipment will meet
your expectations and provide safe operation when it is properly

.

installed and maintained

Checking the contents of package

Please carefully remove the equipment from the carton and inspect. Note
any damage that might have occurred during shipment. Empty the carton to
ensure that small parts are not discarded.

If any damage has occurred during shipment, the local carrier should be
notified at once. A report should be forwarded to SIMCO JAPAN, INC.
The address and other relevant informations are written on the back cover
page.

Package Contents

1

Static bar and high voltage cable typically 3m

1 pc.

)

(

)

2

Mounting Device

)

Model

Device

MEB

MEB Clamp

2 pcs.

MEB CE/RS X1/2 flat plate

2 pcs.

-

(

)

SS-50

X1/2 flat plate

2 pcs.

(

)

SS-50 CE/RS X1/2 flat plate

2 pcs.

-

(

)

A kind of bracket different from the above-mentioned by prior meeting might be
attached.

3

Plastic ties and Plastic blocks

1 set.

)

4

Daily Inspection Label

1 pc.

)

5

Instructions Manual / Warranty

1 pc.

)

Please check if any part is missing or does not have
satisfactory finish. Contact us or our agents
immediately in the event of such occurrence.

-page 2-

CONTENTS

Notes to Users...................................................................................page 1

Receipt of equipment.......................................................................page 2

Contents.............................................................................................page 3

Packing articles and accessories.......................................................page 3

Section 1. General description..........................................................page 4

Section 2. Specifications...................................................................page 5

Section 3. Principle of Operation.....................................................page 7

Section 4. Installation........................................................................page 8

Section 5. Operation........................................................................page 13

Section 6. Maintenance...................................................................page 13

Section 7. Abnormal conditions.....................................................page 17

Section 8. Replaceable parts...........................................................page 18

Section 9. Other products...............................................................page 18

Model A3030/A3031 connectors....................................................page 19

Simco-Ion Air Bars.........................................................................page 20

Simco-Ion EQUIPMENT REPAIR WARRANTY....................enclosed

Explanation of Symbols:

WARNING

ATTENTION / CAUTION

ELECTRIC SHOCK HAZARD

-page 3-

Summary of Contents for Simco-Ion MEB/SS-50














Reviews: