ITW Simco-Ion D167QG Installation And Operating Instructions Manual Download Page 13

Page: 13 / 16

IONIZING AIR NOZZLES

5200378 Rev. F

8. REPLACEMENT PARTS AND ACCESSORIES

Nozzle Body (thru type, standard)

Nozzle Body (Dead end type, standard)

Standard Cable (per foot)

5050049

5050052

4810004

Point Assembly

4100023

Nozzle – Plated

Nozzle – Stainless Steel

Nozzle – Plated without holes

Nozzle – Stainless Steel without holes

4750068

4370122

4750254

4370121

Pipe Nipple – plated ring included

Pipe Nipple – stainless steel ring included

Pipe Nipple – plated terminal included

Pipe Nipple – stainless steel terminal included

5050056

5050057

5050058

5050059

Aircock

4750333

Header Tube

*see below

Pipe Plug

4250050

Pipe Bushing

4250051

Cable Support

4610010

10.

Spring Loaded Connector Kit

5050001

11.

Bracket Nozzle Mount (sold separately)

4510157

* Nozzle spacing on header to be specified by customer. (2” minimum) Contact Simco-Ion for part

numbers

Summary of Contents for Simco-Ion D167QG

















Search results

Summary of Contents for Simco-Ion D167QG

Reviews:

Related manuals for Simco-Ion D167QG

Brands by name

Popular brands

ITW Simco-Ion D167QG, Installation And Operating Instructions Manual

Search results

Summary of Contents for Simco-Ion D167QG

Reviews:

Related manuals for Simco-Ion D167QG

Brands by name

Popular brands