ITT Goulds Pumps API 3171 Installation, Operation And Maintenance Manual Download Page 48 | Manualshive

Page: 48 / 64

background image

Maintenance

Model API 3171 Installation, Operation, and Maintenance Manual

46

2. Remove the pump half coupling hub (233) and key.
3. Remove the locking bolts (370C) and then slide bearing shell (134) assembly with the shaft

out through the motor support (240).

CAUTION:
Two people should handle any shaft over 9 feet long. Improper handling can bend the shaft.

4. Use a screwdriver in order to pry the labyrinth seal (332A) from the bearing shell (134).

NOTICE:
We recommend that you replace the labyrinth seal every time the pump is inspected.

5. Remove the bearing retaining ring (361A).
6. Slide the bearing shell (134) off the bearing and shaft.
7. Remove the locknut (136) and the lockwasher (382).
8. Use a suitable bearing puller in order to remove the bearing (112).

Make sure to save the bearing for inspection.

9. Set the shaft on a table where it is adequately supported.

You do not need to disassemble the pump any further unless you need to replace bad
parts.

Preassembly inspections

Replacement guidelines

Casing check and replacement

WARNING:
Risk of death or serious injury. Leaking fluid can cause fire and/or burns. Inspect and ensure
gasket sealing surfaces are not damaged and repair or replace as necessary.

Inspect the casing for cracks and excessive wear or pitting. Thoroughly clean gasket surfaces
and alignment fits in order to remove rust and debris.
Repair or replace the casing if you notice any of these conditions:

• Localized wear or grooving that is greater than 3.2 mm | 1/8 in. deep

«
...
46
47
48
49
50
...
»

Summary of Contents for Goulds Pumps API 3171

































































Reviews:

No comments

Related manuals for Goulds Pumps API 3171

Evosta2 11/139 SAN V

Brand: DAB Pages: 31

Brand: DAB Pages: 19

Brand: Jecod Pages: 3

Brand: Quantum Pages: 20

Brand: Watts Pages: 37

Pond Clear 5000

Brand: SuperFish Pages: 12

Brand: salmson Pages: 68

Brand: Rinnai Pages: 2

Brand: SFA-SANIFLO Pages: 14

Brand: Becker Pages: 6

Brand: Hamron Pages: 19

Brand: Rietschle Thomas Pages: 48

Brand: Amtrol Pages: 2

Brand: F.F. Group Pages: 28

Brand: Malmbergs Pages: 12

Brand: Grundfos Pages: 8

auroSTOR VIH S GB 300/3 BES

Brand: Vaillant Pages: 24

Brand: Wacker Neuson Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands