GAELIC GOAL - STEP BY STEP ASSEMBLY
W
O
R
L
D
W
ID
E
©
C
O
P
Y
R
IG
H
T
2
0
1
6
IT
S
A
G
O
A
L
P
O
S
T
S
L
T
D
,
A
L
L
R
IG
H
T
S
R
E
S
E
R
V
E
D
A
R
E
G
IS
T
E
R
E
D
D
E
S
IG
N
STEP 5
Insert Arrow Head Net Fixings
into Upright Posts and into crossbar.
FOR EASIER ASSEMBLY
Use a rubber mallet and also spray furniture polish inside posts. Do not use a metal hammer. Do not apply grease or vaseline.
STEP 6
Insert Corner Brackets
X
into the
upright posts
S
(uprights have logos on the side)
STEP 7
Insert T Brackets into
each end of the crossbar,
tighten nuts bolts
STEP 8
Insert Corner Brackets
A
into each end of the
Backbars
STEP 9
Attach Side bars
N
to the ground
back frame, connect both back
bars together with the
straight connector
SC
STEP 10
Attach Upright
O
to
the Side bars
N
STEP 11
Fit the crossbar together
then fit crossbar onto uprights.
L
X
A
H
STEP 12
Join top tubes
P
to elbows
G
and back tubes
Q
and connect
to the goalpost
.
STEP 13
Attach Top Tubes using nuts and bolts.
Fit Ground Anchors over the ground base
see details of use overleaf.
STEP 14
Attach The Net to the Net Fixings.
Start with each corner
TIE A CORD BETWEEN THE
TOP SUPPORT TUBES TO
SUPPORT THE ROOF OF THE
NET (THIS CAN BE LEFT TIED
IN POSITION WHEN DISMANTLED)
The goal net can
be left attached to the
pre-assembled goal post
side frames. After games
detach crossbar and back bar
for storage. We advise fitting the
optional net ties to the side frames and stanchions.
ASSEMBLY & DISASSEMBLY
FASTER
MATCH DAY
ANCHORING YOUR GOAL ON GRASS
- POSITION YOUR GOAL ON A LEVEL PLAYING SURFACE.
PLACE THE MULTI-SURFACE ANCHOR OVER EACH SIDE OF THE GROUND FRAME (POSITIONS
SHOWN) HAMMER THE PEGS DOWN UNDER THE FRAME INTO THE GRASS. ADDITIONAL
ANCHORS OR LARGER PEGS CAN BE PURCHASED FOR USE ON SOFT GROUND OR SAND. THESE
ANCHORS CAN BE USED FOR HARD SURFACES, SUCH AS TARMAC BY USING BOLTS THROUGH
THE MULTI SURFACE ANCHORS INTO CONCRETE PADS. COUNTER BALANCE WEIGHTS CAN ALSO
BE USED (SUPPLIED SEPARATELY). CHAINS ARE AVAILABLE SEPARATELY THAT CAN BE USED TO
SECURE GOALS TO SEPARATE ANCHOR POINTS.
PEG
REMOV
AL
a
b
a
b
OPTIONAL - Net ties are ideal
to fit nets tightly to the side
ground frames and stanchions.
This is ideally when nets are
left attached to the fully
assembled side frames.
WORLDWIDE © COPYRIGHT 2001 ITSA GOAL POSTS LTS, ALL RIGHTS RESERVED A REGISTERED DESIGN
STEP 1
Lay out all Posts & components
UPRIGHT
SECTION
P
Q
O
N
SIDEBAR
SECTION
TOP
STANCHION
TUBE
BACK STANCHION
TUBE
CROSSBAR
SECTION
With insert
CBI
CROSSBAR SECTION
CB
TOP POSTS
BACK BARS
BACK BARS
TP
M
M
STEP 3
Insert Blanking Cap
and insert Large
Quick Release
Buttons into Corner
Bracket X
C O R N E R
BRACKET for
uprights
STEP 4
Insert small quick release black button
into the lower back stanchion connector.
Insert a black Button into the Spigot.
Insert Spigot and insert Large black
buttons into two Corner Brackets X,
connect parts
together
spigot
Lower back
stanchion connector
C O R N E R
BRACKET
Push and Lock
the Small
Quick Release
Push and Lock
the spigots into
STEP 2
Insert small quick release black button into
Spigot and insert into T bracket. Insert
Large Quick Release Buttons into the
T Brackets.
P
G
Q
