ITRON OpenWay OWR-1000-001 Installation Manual Download Page 2

 

Identification

OpenWay Batter-powered Gas Range Extender Installation Guide  

09/22/2009   TDC-0832-000 

 
   

Copyright

©  2009 Itron, Inc. All rights reserved. 
   

Trademark Notice

Itron is a registered trademark of Itron, Inc. 
All other product names and logos in this documentation are used for identification purposes only and may be trademarks or registered trademarks of their respective companies. 
  

Suggestions

If you have comments or suggestions on how we may improve this documentation, send them to [email protected] 
If you have questions or comments about the software or hardware product, contact Itron Technical Support: 
  

Contact

 

Internet: www.itron.com 

 

E-mail: [email protected] 

 

Phone: 1 800 635 8725 

 

 

 

Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation of this device is subject to the following two conditions:  

 

This device may not cause harmful interference.  

 

This device must accept any interference that may cause undesirable operation.  

This device must be permanently mounted such that it retains a distance of 20 centimeters (7.9 inches) from all persons in order to comply with FCC RF exposure levels.  

 

UL Hazardous Locations 

This device is certified under Electrical Equipment for use in Class 1, Division 2, Groups C and D, UL Standard 1604. 

 

Transportation Classification

The Federal Aviation Administration prohibits operating transmitters and receivers on all commercial aircraft. When powered, the  is considered an operating transmitter and receiver and 

cannot be shipped by air. All product returns must be shipped by ground transportation. 

 

Modification and Repairs

To ensure system performance, this device and antenna shall not be changed or modified without the expressed approval of Itron. Any unauthorized modification will void the user’s 

authority to operate the equipment. 
 

  

 

 
Warning  Only authorized Itron personnel should attempt repairs on Itron equipment. Attempts to do so by others might void any maintenance 

contract with your company. 

 

 

 

Summary of Contents for OpenWay OWR-1000-001























Reviews: