ITech IT7300 Series Programming Manual Download Page 42

Page: 42 / 73

TRACe Subsystem Commands

TRACe:FEED:CONTrol

This command is used to select the buffer control. With NEVer selected,

storage into the buffer is disabled. When NEXT is selected, the storage process

starts, fills the buffer and then stops. The buffer size is specified by the :POINts

command.

This value must be set to NEXT before using the Trace subsystem to query

cached data (i.e., execute

TRACe:DATA?

Command syntax

TRACe:FEED:CONTrol <CRD>

Parameters

NEVer | NEXT

Example

TRAC:FEED:CONT NEXT

Query syntax

TRACe:FEED:CONT?

Returns

<CRD>

Related commands

TRAC:FEED

TRACe:DELay

This command is used to set the delay time, which is the time between sending

the

TRIGger[:IMMediate]

command (starting to enter the buffering state) and

storing the value of the first point. Setting this delay time can be used to prepare

for communication with other devices (devices that need to communicate with

IT7300).

Command syntax

TRACe:DELay <NRf>

Parameters

0 to 3600s | MINimum | MAXimum | DEFault

UNIT

S (second)

Summary of Contents for IT7300 Series










































































Search results

Summary of Contents for IT7300 Series

Reviews:

Related manuals for IT7300 Series

Brands by name

Popular brands

ITech IT7300 Series, Programming Manual

Search results

Summary of Contents for IT7300 Series

Reviews:

Related manuals for IT7300 Series

Brands by name

Popular brands