ITech IT7300 Series Programming Manual Download Page 23

Page: 23 / 73

System Commands

will be returned first. when you read all the error tips information in the error

queue. The ERROR led will turn off. When error occur the buzzer of the

power supply will beep once.

⚫

If more than 20 errors occurred, the last one stored in the queue will be
replaced by “-350”,

Meaning "too many mistakes.". If the error

messages in the error message queue are not read out, the error
following will not be saved to the queue. If there is no error message,
when read error information, it will r

eturn “+0”, meaning “no error”.

⚫

If turn off the power supply or send “CLS(clear status) order, the error
messages in the error queue will be cleared. *RST order will not clear the

error messages in the error queue.

SYSTem:CLEar

This command is used to clear the error information.

Command syntax:

SYSTem:CLEar

Parameters

None

Returns:

None

SYSTem:REMote

This command is used to set the power to remote control mode. Only the Shift,

Local, Select, and On / Off keys are available on the front panel, and all other

keys are locked for use. Failure to send this command for remote control

configuration before sending control commands using a PC may cause

communication errors.

Command syntax

SYST:REM

Parameters

None

Query syntax

None

SYSTem:LOCal

This command is used to switch the instrument to local control

Summary of Contents for IT7300 Series










































































Search results

Summary of Contents for IT7300 Series

Reviews:

Related manuals for IT7300 Series

Brands by name

Popular brands

ITech IT7300 Series, Programming Manual

Search results

Summary of Contents for IT7300 Series

Reviews:

Related manuals for IT7300 Series

Brands by name

Popular brands