ITech IT7300 Series Programming Manual Download Page 20

Page: 20 / 73

Remote Control

Baudrate: 9600(4800, 9600, 19200, 38400, 57600, 115200). You could enter

the system menu to set the baudrate.

Data bit: 8

Stop bit: 1

Parity bit: (none, even, odd)

EVEN

8 data bits have even parity

ODD

8 data bits have odd parity

NONE

8 data bits have no parity

Native machine address: (0 ~30, factory default is 0)

Start Bit

8 Data Bits

Parity=None

Stop Bit

1.6.2 USB Interface

Use a cable with two USB ports to connect power supply and PC. You can

program through USB interface to achieve all functions of power supply.

The functions of USB488 interface are as follows:

⚫

Interface is 488.2 USB488 interface

⚫

Receive the following request: REN_CONTROL, GO_TO_LOCAL, and

LOCAL_LOCKOUT

⚫

When the interface receives MsgID = TRIGGER USBTMC command, it will

transmit the TRIGGER command to the function layer.

The functions of power supply’s USB488 are as follows:

⚫

receive all SCPI commands

⚫

device is SR1 enabled

⚫

device is RL1 enabled

⚫

device is DT1 enabled

1.6.3 LAN Interface

Press

(Shift) +

(Menu) on the front panel together to access the

menu. Select LAN in the Communication from System and then configure

Gateway, IP, Mask and SocketPort in the LAN option.

Connect the LAN interface of power supply to the computer with a reticle

(crossed).

1.6.4 GPIB Interface

Use a IEEE488 bus to connect GPIB interfaces of power supply and PC.
Please ensure that the screws have been screwed down in order to have a full

Summary of Contents for IT7300 Series










































































Search results

Summary of Contents for IT7300 Series

Reviews:

Related manuals for IT7300 Series

Brands by name

Popular brands

ITech IT7300 Series, Programming Manual

Search results

Summary of Contents for IT7300 Series

Reviews:

Related manuals for IT7300 Series

Brands by name

Popular brands