background image

-28-

-29-

M a i n t e n a n c e  &  W a r r a n t y

1). Maintenance:

     Replacing the battery and product maintenance:
     a. Remove the battery from the unit if it is not required 
         for extended periods of time in order to avoid 
         damage to the battery compartment and the electrode 
         resulting from a leaking battery.
     b. After power on, if a symbol 

      

appears on the 

         LCD, indicating that you should replace the battery 
         in order to avoid inaccurate measuring reading. 
         Otherwise the battery is very possible leak that will 
         seriously damage the unit life.  
         The battery compartment is on the down rear of the 
         unit, open the battery door, replace the old battery 
         for new battery (notice the battery polarity), close 
         the battery door.
     Cleaning the casing

     Never use alcohol or thinner to clean the unit casing, 
     which will especially erode the LCD surface; just clean 
     the unit lightly as needed with little clean water.
     Never impact the unit or use on humidity condition.
     Do not store or use the unit in following locations where 
     the unit may be subject to:
     a. Splashes of water or high levels of dust.
     b. Air with high salt or sulphur content.
     c. Air with other gases or chemical materials.
     d. High temperature or humidity (above50

, 90%,) or 

         direct sunlight.

2). Warranty:

About relative warranties please read provided 
warranty card.

We disclaim any liability due to: transportation 
damages; incorrect use or operation; manipulation, 
alterations or repair attempts; without warranty card, 
invoice.

3). Specific Declarations:
      a. The product design and the manual updating, 
           repairing by technician authorized by us, do not try 
           any alternations or repair attempts.
      b. Disposal of battery should in accordance with local 
          laws and regulations. 

Summary of Contents for GM8902

















Reviews: