background image

-10- 

Main part 

of faucet

Stainless steel 

faucet

Inlet water 

connection

                             

 

Diagram 7                                                                                  Diagram 8

 

 Wastewater pipe installation 

Using a drill, make a φ6.2mm hole into the sink pipe drain. Take out an appropriate length of the 6mm pipe.   
One end should be inserted into the small hole (see diagram 8).    Put some silica gel where the 6mm pipe 

and  the  drain  pipe  connect  to  prevent  leakage.    Then,  using  a  cable  tie,  fix  the  wastewater  pipe  to  the 

drain pipe. 

 Side stream RO membrane installation method 

Take  the  water  purifier  out  of  the  package  carton.  Open  the  machine  cover.  Unscrew  the  nut  of  the 

membrane  housing cap  to  remove  the inlet  housing  pipe.  Open  the  housing  cap  by membrane housing 

wrench.  Check  if  the  vacuum  packing  of  RO  membrane  is  leaking.  If  not,  take  the  membrane  from  its 

packaging. Make sure there are 4 

“O” rings in one end of the membrane central tube and 2 “O” rings in the 

other end. Check whether there are expansion and deformation 

“O” rings, if not, insert the 4    “O” rings end 

into  the  membrane  housing  tightly(See  Diagram  9),  finally  ,  screw  the  housing  cap,  take  membrane 

housing wrench to tighten the cap. Insert the inlet pipe to the housing cap, screw the nut. Put the housing 

into the single clip and close the machine cover. 

   

 

Warnings: 

 

When installing the RO membrane you should pay attention to the direction of the membrane; 

 When installing the RO membrane, Make sure there are 4 

“O” rings in one end of the membrane central 

tube and 2 

“O” rings in the other end. Check whether there are expansion and deformation “O” rings

 

 When installing, be sure to insert the end with 4 O-rings into the membrane housing.    Be sure when 

installing to only use a little force to put the RO membrane into the membrane housing. If you encounter 

too  much  resistance,  please  do  not  force  the  reverse  osmosis  membrane  into  the  membrane  housing, 

doing  so  may  cause  permanent  damage  to  the  membrane  housing  or  membrane  components  (the 

manufacturer does not assume responsibility for returned components due to damage during installation); 

 Damage to the membrane housing and reverse osmosis membrane element caused as a result of the 

above reasons is not covered under the water purifier warranty. 

Summary of Contents for CR500-A-S-1

















Reviews: