background image

  

 

MEASUREMENT AND ASSEMBLY MANUAL 

 

Instruction validity: as of 1 August 2013 

13 

10. MAINTENANCE 

It  is  recommended  to  carry  out  regular  maintenance  of  the  roller  blind  every  two  years.  No  maintenance  activities  are 

expected to be done by the user, except for fabric cleaning, if necessary.  

FABRIC CLEANING 

Fabric

 

Cleaning

 

SATIN, SATINÉ BLACKOUT, SCREEN NATURE,  
SATINÉ METAL, SCR3005

 

Clean  with  a  brush,  or  wipe  with  a  cloth  damped  in  a 
solution of water and a neutral detergent. Do not scrub by 
force. 

SOLTIS 92

 

Wipe  with  a  cloth  damped  in  a  solution  of  water  and  a 
neutral  detergent.  Do  not  use  alcohol-based  stain 
removers. Do not scrub by force. 

 

SCREEN ZIP 

 

DEFECT

 

POSSIBLE CAUSE

 

SOLUTION

 

Fabric does not roll properly; 
fabric side displacement

 

Uneven fabric thickness 
(manufacturing defect of the fabric). 

Apply  a  distance  layer  (e.g.  adhesive 
tape) directly onto the winding drum, on 
the  side  opposite  to  where  the  fabric  is 
moving. 

Repeat 

applying 

further 

adhesive  tape  layers  until  the  defect  is 
completely removed. 

Drum cover displacement. 

If  there  is  no  gap  at  the  end  covers  for 
the  fold,  or  if  drum  cover  is  used,  open 
the  box  and  make  sure  there  is  no 
displacement  to  either  side.  If  so, 
provide for centring. 

Fabric is not centred in guide bars. 

Open  the  box  and  check is  the  fabric  is 
centred  with  respect  to  the  two  guide 
bars. 

Roller blind is not rectangular. 

Series  Z roller  blinds  have  very  low 
tolerance, thus perfect alignment is vital 
for  the  proper  function.  Check  the  roller 
blind  for  deformation  and  whether  it  is 
installed  at  right  angles.  Check  any 
unevenness of walls or other supporting 
elements  which  can  cause  deformation 
between two sides of the structure. Use 
distancing elements if necessary. 

Roller blind does not draw up 
fully 

Winding drum axis is disconnected 
from the support. 

Remove  the  box  and  check  proper 
connection of the winding drum. 

Summary of Contents for SCREEN ZIP















Reviews: