10A
-
5. How To Control The Unit
You can operate the unit in three ways:
1. By master/slave built-in preprogram function
2. By easy controller
3. By IL-0824 ( please refer to the user guide of iLead controller ) or universal DMX
controller
No need to turn the unit off when you change the DMX address, as new DMX address setting
will be effected at once. Every time you turn the unit on, it will show IM-8W on the display and
move all the motors to their
‘
home
’
position and you may hear some noises for about 20
seconds. After that the unit will be ready to receive DMX signal or run the built-in programs.
5.1. Master/Slave Built-In Preprogrammed Function
You can select blackout mode
in
(yes blackout) or
(no blackout)
mode while the unit is turned on. By linking the units in master/slave connection, the first unit
will control the other units to give an automatic, sound activated, synchronized light show. This
function is good when you want an instant show. You have to select
(show 1) or
(show 2) mode by easy controller. Its DMX input jack will have nothing plugged into it,
and Its master LED will be constantly on and sound LED will flash to the music. The other
units will have to set in slave mode
and select
(normal) or
(2 light
show) mode, Their DMX cables plugged into the DMX input jacks (daisy chain) and the slave
LED lights will constantly on.
2-light show
In
(slave mode),
means the unit works normally and
means
2-light show. In order to create a great light show, you can set
on the second unit to
get contrast movement to each other, even if you have two units only.
5.2
.
Easy Controller
The easy remote control is used only in master/slave mode. By
connecting to the 1/4
”
microphone jack of the first unit, you will find that
the remote control on the first unit will control all the other units for
Stand by, Function and Mode.
Channel Mode
Press the
MENU
button up to when the
is shown on the display. Pressing
ENTER
button and the display will blink. Use
DOWN
and
UP
button to select the
(16 Channel ) or
(8 Channel) mode. Once the mode has been selected, press
the
ENTER
button to setup or automatically return to the main functions without any
change after 8 seconds. To go back to the functions without any change press the
MENU
button again.
Show Mode
Press the
MENU
button up to when the
is showing on the display. Pressing
ENTER
button and the display will blink. Use
DOWN
and
UP
button to select the
(show 1) or
(show 2) or
(show 3) or
(show 4) mode. Once the mode has been
selected, press the
ENTER
button to setup or automatically return to the main functions
without any change after 8 seconds. To go back to the functions without any change press the
MENU
button again.
Show 1 mode - Fixture is placed on the floor. Tilt movement angle 210
°
.
Show 2 mode - Fixture is fixed under ceiling. Tilt movement angle 90
°
.
Show 3 mode - Fixture is placed on the speaker, The spot is always projecting
to the audience
’
s direction; i.e in front of the stage. Pan movement angle ( left to
right to left ): 160
°
. Tilt movement angle: 90
°
( 60
°
above horizon; 30
°
below
horizon.)
Show 4 mode - Fixture is fixed under ceiling. The spot is mainly projecting in
front of the stage. Pan movement angle ( left to right to left ) :160
°
. Tilt movement angle:
90
°
( vertically, front 75
°
; back 15
°
)
Slave Mode
Press the
MENU
button up to when the
is shown on the display. Pressing
ENTER
button and the display will blink. Use
DOWN
and
UP
button to select the
(normal) or
(2 light show) mode. Once the mode has been selected, press the
ENTER
button to
setup or automatically return to the main functions without any change after 8 seconds. To go
back to the functions without any change press the
MENU
button again.
