background image

3. INSTALLATION

 

ITA Series – Table Top Precision Weighing Balance

ITA Series – Table Top Precision Weighing Balance

3.1

Unpacking

a) ITA/ITB -AS/AP/AW

Save the packaging material. This packaging ensures the best possible 
protection for the storage or transport of the product.

3.2

Placing your Scale

3.3

Leveling the Scale

3.4

Power Source

3.5

Calibration Check

Unpack and verify that the following components have been 
included:

 Scale

b)

Instruction Manual

c)

AC Adapter / Attached power cord (customer specific)

Before you install the scale, identify the best location for the equipment. 
The proper environment enhances its operation and longevity. Keep in 
mind the following factors, which might have a negative influence on 
the Scale’s operation: 

a) Vibration

:  Vibration  diminishes  the  scale’s  ability  to  measure 

accurately. Electrical machinery such as conveyors and drill presses 
can cause inaccurate and non-repeatable readings. The scale may 
also  read  inaccurately  if  it  is  not  leveled  properly.  The  scale 
incorporates a QUICK weighing mode where the scale can reject 
readings with vibration up to some extent.

b) Drafts / Air currents

: Moving air can cause the scale to read wind 

movement as an additional force and cause inconsistency in the 
weighing results. 

c)

External Rubbing / Friction:

 A scale cannot measure accurately 

if an object is rubbing or pressing against the scale platform.

Level the scale by rotating the adjustable feet. It is leveled correctly 
when the bubble scale is in the center of the circle. 

The  unit  comes  with  12V  AC  adaptor  or  220V  AC  as  per  model 
specifications / country of use. The scale is fitted with a built in 6V 4Ah 
battery which provides backup of more than 35 – 50 hours depending 
on glow setting and sleep mode setting.

Put a known weight on the machine and make sure that the scale reads 
the correct weight on the display. In case of a variation in the display 
reading,  it  is  recommended  to  calibrate  the  scale  again  with  the 
procedure explained later in the manual.

2

11

STEP

DISPLAY

PROCEDURE

5.

6.

7.

8.

9.

10.

11.

Press ZERO and the display show “CAP”.   
Press  Zero and the display will now show 
the current capacity. Enter the capacity as 
“30.000”  if  you  wish  to  make  capacity 
30kg.  Note  the  decimal  point  is 
automatically  shown  as  per  previous 
setting  in  step  3  &  4.  You  can  enter  the 
capacity  by  using  Mode  for  shifting  the 
digit to left and Tare Button for changing 
the digit.

Make sure there is no weight on the pan. 
Press Zero and the display shows “noLoAd” 
momentarily and shows the counts at zero 
level. 

Pause for 2 seconds at the previous step 
and press Zero. The display shows “LoAd” 
momentarily  and  shows  the  internal 
counts. 

Put a known weight on the weighing pan 
(Ex.: 10kg). Press the Zero key. The display 
will now show all “000.000” with the units 
digit blinking.

 
If you put 10kg weight, Enter the weight in 
grams “010000”. Change the blinking digit 
by  pressing  the  tare  button.  Shift  the 
changed digit to left by pressing the mode 
button once.

Press the zero key once again 

With the weight still on the pan, press Zero 
key  once  again  to  return  to  weighing 
mode. Check calibration.

 

 

 

 

 

 

 

 

 

 

Summary of Contents for ITA SERIES









Reviews: