ISG 601-502 Instructions Manual Download Page 15 | Manualshive

Page: 15 / 19

ISG 601-502 Instructions Manual Download Page 15

1_Operation

Condenser_

Remove the slide back and fall the condenser down a little.

One drop of oil could be placed in the top of condenser by through the long aperture of stage.

Then move the slide forward and lift the condenser up

Objectives_

Turn the nosepiece and take the objective out of the optic path. Place one drop of oil on the slide then

turn the condenser slowly and mount the objective.

2_Air bubble in oil immersion

a) Never make the oil immersion into your eyes. Please take following steps as soon as the

oil immersion touches your skin or eyes.

Use soap or clean water to wash your skin carefully.

Please wash your eyes with clean water (at least wash 15 minutes) and go to the hospital

at once.

b) Do not expose the oil immersion in the sun or ultraviolet radiation directly.

As the air bubble in the oil immersion will make bad affect to the quality of image, please

make sure that there is no air bubble in the oil immersion before use. Please check the air

bubble as following, remove the eyepieces and open the view field diaphragm and aperture

diaphragm entirely then observe the exit pupil which is light and in nummular shape.

c) Remove the air bubble as following.

Turn the nosepiece slowly and turn the oil immersion objective once or twice.

Turn the lifting knob for condenser slowly and make the condenser a little bit of up and

down.

Increase the amount of oil immersion or change the old oil immersion with new one

3_Operation for oil immersion

Use the oil immersion as little as possible. The oil immersion will be conglutinated to the

stage and condenser and this will have bad effect the performance if there is too much oil

immersion. Please clean the redundant oil on the objective and condenser after finishing

the observation otherwise the image will be affected. Use the aether to clean the oil then

use the pure alcohol (ethanol or carbinol) to make entirely cleaning. Please repeat the clean

three or four times.

_ Notice:

Please follow the instruction from manufactures when the aether or pure alcohol is used.

Keep them away from the fire or electronic spark

4_Attention

_ Keep the bottle for oil immersion sealed as much as possible and check it periodically

_ Never press the bottle overly as it may caused oil gushed out of the bottle

_ Clean the out surface of the bottle from remanent oil

11.Adjusting the coarse focusing knob’s tension

«
...
13
14
15
16
17
...
»

Summary of Contents for 601-502




















Reviews:

No comments