Iseki SRE2600X, Instructions For Use Manual

Page: 45 / 92

456939_a 45
Installation
IMPORTANT!
Danger of damaging the boundary
cable
If the boundary cable is damaged or cut,
the transmission of the control signals to
the appliance is no longer possible. In
this case, the boundary cable must be re-
paired or replaced. Boundary cables can
be obtained from the manufacturer.
■
Always route the boundary cable dir-
ectly on the ground. If necessary, se-
cure with an additional lawn peg.
■
When laying the boundary cable and
during operation, protect the bound-
ary cable from damage.
■
Do not dig or scarify in the vicinity of
the boundary cable.
1. Lead the boundary cable at least 1 m straight
from the base station (01/a).
2. Attach the boundary cable at regular intervals
with lawn pegs or route it underground (at a
max. depth of 10 cm).
3. Route the boundary cable around obstacles:
see chapter 4.5.3 "Excluding obstacles",
page 45 .
4. Create corridors between individual mowing
areas: see chapter 4.5.4 "Enclosing corridors
(01/i)", page 45 .
5. Exclude excessive upward or downward
slopes: see chapter 4.5.5 "Excluding down-
ward slopes", page 45 .
6. Create loops of cable: see chapter 4.5.6
"Creating loops of cable (08)", page 46 .
7. From a distance of at least 1 m, guide the
boundary cable straight to the base station
(01/k).
8. After completing the routing of the boundary
cable, connect to the connector (04/7) of the
base station: see
chapter 4.5.1 "Connecting
the boundary cable to the base station (04)",
page 44
.
4.5.3 Excluding obstacles
Depending on the surroundings of the working
area, the boundary cable must be routed at differ-
ent distances to obstacles. Use the ruler that can
be removed from the packaging to determine the
correct distance.
NOTE
Exclusions are only necessary if they
cannot be detected by the bump sensors
of the automatic lawn mower. Avoid too
many or unnecessary exclusions.
Distance from walls, fences, beds:
min. 15 cm (01)
The appliance moves along the boundary cable
with an offset of 15 cm to the outside. Therefore,
route the boundary cable at a distance of at least
15 cm from walls, fences, beds, etc.
Distance from terrace edges and paved
paths (06)
If the terrace or path edge is higher than the
grass surface, a distance of at least 15 cm must
be complied with. If the edge of the terrace or
path is at the same height as the grass surface,
the cable can be routed exactly along the edge.
Distance of obstacles from the boundary
cable (01)
If the boundary cables are precisely folded up
away from the obstacle or towards the obstacle,
i.e. distance 0 cm, the appliance moves beyond
the boundary cable. The boundary cables must
not be crossed over (01/g).
Routing the boundary cable around
corners (07)
■
For inwards going corners (07/a): Route the
boundary cable diagonally to avoid the appli-
ance becoming caught in the corner.
■
For outwards going corners with obstacles
(07/b): Route the boundary cable in a point in
order to avoid a collision of the appliance with
the corner.
■
For outwards going corners without
obstacles: Route the boundary cable at an
angle of 90°.
4.5.4 Enclosing corridors (01/i)
In the corridor the following distances must be
complied with:
■
Total width: min. 60 cm
■
Distance of the boundary cable to the edge:
15 cm
■
Distance between the boundary cables: min.
30 cm
4.5.5 Excluding downward slopes
Downward slopes that are greater than 40 %
must be excluded with the boundary cable (40 %
= 40 cm downward slopes per 1 m horizontally).