Iseki 1812001, Owner'S Manual

Page: 4 / 31

4
546336.B.9
Original version
designed. If you have any doubts contact your authorised dealer.
Do not modify the design of the machine.
Operator Competency
Do not allow persons to operate machinery without full and proper
instruction in the use of the machine, adjustments maintenance and
the factors of safe operation.
Please read and understand this manual and the engine instruction
manual before assembly and use.
• When working with the machine wear close-fitting work
clothes, sturdy work gloves, eye protection, ear muff, dustproof
mask and antiskid shoes.
• The operator must understand all the safety requirements
detailed in this manual before using the equipment.
• The operator is responsible for the safety of all third parties while
the equipment is in use.
• The use of alcohol, prescription or non-prescription drugs may
impair the user’s ability to properly assemble or safely operate
this chipper shredder.
• Do not operate this machine under the influence of alcohol or
drugs.
• If you have any queries regarding these instructions, contact
your local dealer for clarification before you use your unit.
• The unit must be correctly assembled before use. Failure to
follow the manual’s instructions could result in serious damage
or injury.
• Ensure that the unit is on a level and stable surface before
operating.
• Ensure all fuel hoses are in good condition and have been
correctly fitted.
• The chipper shredder should be carefully checked for operational
safety every time before use.
• Carbon monoxide can be extremely dangerous in enclosed
areas; do not run the machine in an enclosed area since the
exhaust from the engine contains carbon monoxide, which is
colourless, odourless and tasteless.
• Do not place hands or any other part of the body or clothing
inside the feeding chutes, discharge area, or near any moving
part.
• When chipping short or block wood material, it is strictly
forbidden to stand in front of the Inlet chute opening. The
operator should stand on the side of the inlet chute and put the
materials into the inlet chute in order to prevent any personal
injury.
• Do not get close to the outlet chute, the chips are expelled from
the outlet chute can hurt you or may cause serious injury.
• Before inspecting or servicing any part of the machine, shut off
the power source. Make sure that all moving parts have come to
a complete stop. Disconnect the spark plug wire from the spark
plug.
• Use the correctly specified fuel with this unit.
• The machine is rated with the sound pressure level of
95.38dB(A) and the sound power level of 115.38dB(A) (The
sound pressure value and sound power value are measured
according to EN ISO 3744:1995 and EN ISO 11201:2010
standards respectively with the uncertainty k=3dB). Consider the
surrounding environment before using this machine as the noise
may not be acceptable around places like office, lab or hospitals.
Check local rules and regulations for allowable noise pollution in
your region.
• Keep blade sharp and grease bearing regularly which can help
keep noise to relatively lower level.
• The GX390 engine is shipped from the factory without oil and
fuel. Remember to fill 1.1L 10W-30 oil and Clean Unleaded
Gasoline before starting the machine for first time;
• Remove and replace engine oil after 5 hours running time, and
then replace the oil with 50 hours regular running times.
• The GX390 engine uses clean unleaded gasoline as fuel.
Gasoline is flammable and explosive. Keep machine far away
from flammable and explosive objects and fire source when
using or maintaining.
• When filling gasoline and oil, the engine must be shut down.
• Before starting machine, it is necessary to ensure that all shock
pads (part 6 and 14 shown in assembly section) are extended
in contact with the ground and the belt protective cover, the
bearing protective cover is intact.
• Do not leave the chipper shredder unattended when it is running.
• Onlookers should be kept a safe distance away from the chipper
shredder when it is in use.
• Keep children and animals well away while the unit is in use and
while it is slowing down.
• Never try to move the unit when the engine is running, or before
it has had time to stop.
• Parts of the engine do get extremely hot and could cause
serious burns.
• The person operating this unit should pay constant attention to
the material being processed.
• The operator should remain at the unit at all times when it is
running.
• Ensure that the engine is turned OFF while the unit is
unattended.
• Do not overload the machine and operate it over its maximum
chipping capacity.
• Do not attempt to repair the machine unless you are competent
to do so.
• Keep the engine clean of debris and other accumulations to
prevent damage to the engine or possible fire.
• Remove any debris inside the Inlet chute each time after the
engine is turned off.
• Do not over-reach. Keep proper balance and footing at all times.
• Do not tamper with the engine governor settings on the
machine: the governor controls the maximum safe operating
speed and protects the engine and all moving parts from
damage caused by over speed. Seek authorized service if a
problem exists.
• Feed only clean material into the machine. Foreign matter like
soil, sand, grit, stones, pieces of metal, etc. will damage the
sharp edge of the cutting knives. Root balls and dead wood will
also blunt the blades quickly. Operating the machine with blunt
blades causes excessive vibration which may result in damage
to the machine.
• Do not feed short, stubby pieces of wood into the machine,
as they tend to bounce and spin in the Inlet chute. Feed these
short pieces together with longer pieces. After becoming
familiar with the machine, prune to suit its capabilities.
• While operating the machine keep a wooden stick handy,
approx 30mm diameter x 1m long. This stick will be useful for
pushing in short, brushy and very leafy materials and to keep
the infeed chute clear.
• The engine is fitted with oil alert and will not start if the oil level
in the sump is too low. It may also stop if it is operated on a
steep slope.
• Keep all guards and deflectors in place and in good working
condition.
• Because the chipper is self-feeding and has a large infeed
opening, the machine can easily be stalled with branches that
are too big for processing. You will have to hold these branches
back and feed the machine with care until you are familiar with
its capacity.
• Do not overload the chipper. If the drum is slowing down, feed
the material in slower.
• The Manufacturer’s Warranty may be voided by the incorrect use
of this product.
The Manufacturer or their Agents can accept no liability for any
material that is processed and causes personal discomfort or injury.