ISA T2000 User Manual Download Page 5 | Manualshive

Page: 5 / 110

background image

DOC. MIE11110 Rev. 5

Page 5 of 110

SAFETY AT WORK

The Product hereafter described is manufactured and tested
according to the specifications, and when used for normal
applications and within the normal electrical and mechanical
limits will not cause hazard to health and safety, provided that
the standard engineering rules are observed and that it is used
by trained personnel only.

The application guide is published by the Seller to be used
together with the Product described in the corresponding
document. The Seller reserves the right to modify the guide
without warning, for any reason. This includes also but not
only, the adoption of more advanced technological solutions and
modified manufacturing procedures, and also the addition of other
features, not available in the first release.

The Seller declines any difficulties arising from unknown
technical problems. The Seller declines also any responsibility in
case of modification of the Product or of any intervention not
authorized by the Seller in writing.

The warranty includes the repair time and the materials necessary
to restore the complete efficiency of the Product; so, it

does not

include other burdens, such as the transport and customs fee.

Under no circumstances

the warrantee includes any cost that

the User may have suffered because of the Product unavailability
and downtime.

The Product is CE marked, and has been tested to operate
according to EN 61010-1, with the following operating conditions:
. Pollution degree 2: normally, non conductive pollution occurs;
. Measurement category 2, for measurement inputs;
. Altitude: less than 2000 m;
. Operating temperature: 0 to 50 °C; storage: -20 °C to 70 °C;
. Relative humidity : 10 - 80% without condensing;
. Inputs/outputs protection: IP 2X: CEI 70-1 for all but high
voltage outputs; IP4X for high voltage outputs;
. The test set is portable, using the handles.

«
...
3
4
5
6
7
...
»

Summary of Contents for T2000















































































































Reviews:

No comments

Related manuals for T2000

Brand: Raymarine Pages: 55

Brand: Halyard Pages: 4

Underwater Light Show & Fountain

Brand: GAME Pages: 2

Brand: Taylor Made Pages: 2

Brand: York Fitness Pages: 18

Brand: Safco Pages: 2

Brand: Omni Pages: 193

Brand: Raymarine Pages: 70

Brand: Harbor Freight Tools Pages: 4

Brand: Yamaha Pages: 78

Brand: Fast Pages: 42

Brand: DARAY Pages: 28

Brand: Backyard Play Systems Pages: 64

Brand: Haenim Pages: 2

Brand: parr Pages: 20

Brand: Landoll Pages: 71

Brand: York Fitness Pages: 4

Brand: W&H Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands