background image

3280-dda.ib.doc 

page 15 of 16

 

23/07/2002 

Warranty & service

 

 
Equipment is covered by a limited warranty period of three years from date of first delivery unless contrary 
conditions apply under a particular contract of supply. For situations when “

No Fault Found

” for repairs, a 

minimum charge of $A100.00 will apply, whether the equipment is within the warranty period or not. 
 
Equipment warranty is limited to faults attributable to defects in original design or manufacture. Warranty on 
components shall be extended by IRT only to the extent obtainable from the component supplier. 

 
Equipment return: 

Before arranging service ensure that the fault is in the unit to be serviced and not in associated equipment. If 
possible, confirm this by substitution. 
 
Before returning equipment contact should be made with IRT or your local agent to determine whether the 
equipment can be serviced in the field or should be returned for repair. 
 
The equipment should be properly packed for return observing antistatic procedures. 
 
The following information should accompany the unit to be returned: 
 

1.  A fault report should be included indicating the nature of the fault 
2.  The operating conditions under which the fault initially occurred. 
3.  Any additional information which may be of assistance in fault location and remedy. 
4.  A contact name and telephone and fax numbers. 
5.  Details of payment method for items not covered by warranty. 
6.  Full return address. 
7.  For situations when “

No Fault Found

” for repairs, a minimum charge of $A100.00 will apply, whether 

the equipment is within the warranty period or not. 

 
Please note that all freight charges are the responsibility of the customer. 
 
The equipment should be returned 

to the agent who originally supplied the equipment or, where this is not 

possible

, to IRT direct as follows. 

Equipment Service 
IRT Electronics Pty Ltd 
26 Hotham Parade 
ARTARMON 
N.S.W. 2064 
AUSTRALIA 
 
Phone: 

61 2 9439 3744 

Fax: 

61 2 9439 7439 

Email: [email protected] 

IRT 

Communications 

www.irtcommunications.com

Summary of Contents for DDA-3280






















Reviews: