IROX EBR808C, Instruction Manual

Page: 22 / 24

~P.22~
(ENG)
1. To retrieve manually the specific sensor temperature reading, press CHANNEL key until desired channel
number is displayed.
2. To enable auto-scroll function, use CHANNEL button to select channel 1, 2, ... until auto scroll icon
appears on the left hand corner of the 3rd line display.
DCF 77 RADIO CONTROLLED CLOCK
The built-in radio controlled clock is designed to synchronize the time automatically once the unit is
brought within the range of the Frankfurt DCF 77 radio signal. When the unit is receiving the signal, the
radio reception “ ” icon will start flashing and during this reception all manual settings are disabled.
The time reception may take, depending on the signal strength, up to 10 minutes.
When the time reception is complete, the “ ” icon will stop blinking and the following result is shown:
: Last reception was successful
No radio clock tower : Last reception was not successful
You may start a new reception manually. To enable this feature, press & hold the [ ] button for 3-5
seconds. The radio reception signal “ ” icon will start flashing.
If you wish to disable the time reception while it is active in order to perform an operation on the unit,
press the [ ] button. The radio signal “ ” icon will stop blinking and the tower will be shown without
waves.
Pleas note:
The radio controlled clock will start to receive the time automatically in the early morning hours.
SET THE CLOCK, CALENDAR & LANGUAGE
1. Press & hold [CLOCK] button for 2 seconds to enter clock setting mode. Flashing 24 hours will appear.
2. Press [ ] or [ ] button to switch between 24 hours and 12 hours format, and then press [CLOCK]
button to confirm.
3. The hour digits will flash. Use the [ ] button to increase by one hour or [ ] button to decease by one
hour to your desired hours. Holding down either button will change the increment unit rapidly. Press
[CLOCK] button to confirm.
4. The minute digits will flash. Use the [ ] button or [ ] button to set your desired minutes. Holding down
either button will change the increment unit rapidly. Press [CLOCK] button to confirm.
Note: Every change of minute digit will automatically reset the seconds to zero.
5. The year digit will flash and Yr icon appears. Press [ ] or [ ] button to set your desired year. Press
[CLOCK] button to confirm.
Note: Year range is from 2000 to 2099.
6. D and M icons will flash. Press [ ] or [ ] to select D M (Date Month) or M D (Month Date) format. Press
[CLOCK] button to confirm.
7. Month digits will flash. Press [ ] or [ ] button to set your desired month. Press [CLOCK] button to
confirm. Do the same to set Date.
Note: The weekday will be automatically calculated and displayed for the date set above.
8. E digit will flash. Press [ ] or [ ] button to switch 5 languages display of weekday (English/German/
French/Spanish/Italian. See table 1). Press [CLOCK] button to confirm and exit setting mode.
Note: If no key press during setting mode for 10 seconds, it will automatically keep the setting and exit
to normal display.
TO SET DAILY ALARM
1. In clock time display mode, press [CLOCK] button twice to switch to display alarm time for 10 seconds.
2. Press and hold [CLOCK] button for 2 seconds to enter alarm setting mode.
3. The hour digits will flash, use [ ] button to increase by one hour or [ ] button to decease by one hour
to your desired hours. Holding down the button will change the increment unit rapidly. Press [CLOCK]
button to confirm.
4. The minute digits will flash. Use [ ] button to increase by one minute or [ ] button to decease by one
minute to your desired minutes. Holding down the button will change the increment unit rapidly. Press
[CLOCK] button to confirm and finish the setting.
CRYSTAL WEATHER ICON ILLUMINATION CYCLE
1. Press and hold [UNIT] for 2 seconds, the digits of the illumination cycle for the crystal weather icon
start to flash.
2. Press and hold [ ] or [ ] button to select the duration: 5 minutes, 10 minutes, 20 minutes, 30 minutes
and 60 minutes.