Irontite Products Van Norman 794-8688-06 Instruction Manual And Parts List Download Page 52

Page: 52 / 60

FG5000/FG10000 Flywheel Grinder

800-553-5953

COMMON

CONTROL BOX COMPONENT IDENTIFICATION

PART #

DESCRIPTION

794-8626-01

Terminal Block Strip

(TB1 is on the bottom then count up, TB2, TB3, etc.)

A on the left

794-8016-71

Printed Circuit Board

794-8625-15

Relay for Power Column (3)

794-8625-15

Relay for Auto Grind (2)

794-8691-45

Table Motor Contactor

794-8691-46 / 47 Grinding Motor Contactor (794-8691-46 - FG5000), (794-8691-47 - FG10000)

794-8691-57

Table Motor Overload Relay

794-8691-63 / 54 Grinding Motor Overload Relay (794-8691-63 – FG5000), (794-8691-54 – FG10000)

794-8132-69 / 68 Fuse (3) 220x3 (794-8132-69 – FG5000, 30 Amp), (794-8132-68 – FG10000, 60 Amp)

794-8676-78

Transformer

794-1421-17

7 Amp Fuse (under the K)

794-8687-76

Bridge Rectifier

794-8687-74

Auto-Grind Current Sensor

Summary of Contents for Van Norman 794-8688-06


























































Search results

Summary of Contents for Van Norman 794-8688-06

Reviews:

Related manuals for Van Norman 794-8688-06

Brands by name

Popular brands

Irontite Products Van Norman 794-8688-06, Instruction Manual And Parts List

Search results

Summary of Contents for Van Norman 794-8688-06

Reviews:

Related manuals for Van Norman 794-8688-06

Brands by name

Popular brands