Check foot bolts regularly and tighten
as needed. Only use the Ironmaster
Step bench on a level non skid surface.
Failure to tighten bolts adequately will
result in a wobbly bench.
Excessive sweat and moisture can
cause damage to paint, finish and
upholstery. Regular cleaning after
workouts will significantly improve the
condition of your bench as well as
extend longevity.
Maintenance and Troubleshooting:
The Super Bench PRO is of very robust construction and will provide many years of trouble-free operation. For best
performance, please follow these simple steps for maintenance and increased product longevity.
1. Make sure to check and tighten (if needed) the four foot bolts on a regular basis. If bolts are discovered to be
loose, do not use the bench until bolts are retightened to approx 30 ft lbs.
2. The main pivot bolt needs to be checked on occasion. If this bolt loosens over time, the bench will not feel as sol-
id. You will require 2x 19mm wrenches to tighten this bolt. However, use care, if over-tightened the bench will not
function properly as the seat deck frame will be unable to rotate freely to sit into the lower frame and therefore it
will be difficult to bring the bench back to a full prone position.
3. Lubrication—yearly or as needed. The portion of the frame where the upper frame and lower frame meet is pre-
lubricated from the factory with a generous amount of grease. Over time, this can become dirty/dried out and lead
to premature rubbing/wear. If lubricant is overly dirty or dried out, wipe the area clean with a dry cloth and re-
lubricate the area with a light general grease where the seat frame base and lower frame meet when the bench
seat is down. Also use a sparing amount of general purpose grease or oil on the locking lever area contact points
(after cleaning).
The pivot bolt needs to be checked
periodically. If seat has a slight side
to side movement, tighten until
movement ceases. Do not over
tighten as it will impede movement.
Check for adequate lubrication
where the bottom of the seat frame
meets the lower frame as shown.
Use a light general grease in both
the pivot area and lever locking
mechanism (not pictured)
Warranty Information:
Ironmaster warrants to the original purchaser that this Home Fitness Product will be free from defects in workmanship and materials for a specific peri-
od from date of purchase based on the part type listed below. During the warranty period, Ironmaster will either repair or replace, at its option, defec-
tive part(s) at no charge. Warranty covers in home use only.
1 year for normal wear items such as rubber, upholstered parts and surface finishes.
10 years for frame and structural components.
Shipping costs are not included in the warranty and some items may need to be sent to Ironmaster for repair or replacement. Installation of any parts
and labor involved is not included. The warranties described above shall be the sole and exclusive remedy available to the purchaser. Correction of
defects, in the manner and for the period of time described above, shall constitute complete fulfillment of all liabilities and responsibilities of Ironmaster
to the purchaser with respect to the product, and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or
otherwise. In no event shall Ironmaster be liable or in any other way responsible for damages or defects in the product which were caused by repairs
or attempted repairs performed by anyone other than Ironmaster or Authorized service Contractor. This warranty shall not apply if the defect was
caused by misuse, neglect or normal wear and tear of the product purchased. Nor shall Ironmaster be liable or in any way responsible for any inci-
dental or consequential economic or property damage. Some states do not allow the exclusion of incidental or consequential damage, so the above
exclusion may not apply to you.
For customer service, contact your local distributor or:
Ironmaster LLC,14562 167th Ave SE Monroe, WA 98272 USA
Web site: www.ironmaster.com Email: [email protected] Tel: 800-533-3339 or 1-360-217-7780
