irinox CP One Use And Maintenance Instructions Download Page 3

3

SAFETY INFORMATION

            Below are the main general Safety
            Standards:

do not touch the machine with humid or wet 
hands or feet
do not work on the machine with bare feet
do not insert screwdrivers, kitchen tools or 
any other object between the protections and 
moving parts
before performing any cleaning or routine 
maintenance operation, disconnect the 
machine from the electrical power supply by 
turning the main switch off and removing the 
plug
do not pull the power supply cable to discon-
nect the machine from the power supply 
mains.

If the power supply cable is damaged it 
must be replaced by the manufacturer,

by a service centre, or by qualified staff in 
order to avoid risks. 
Non-mobile equipment, not equipped with 
disconnection devices from the power supply 
having a contact separation of all poles that 
provides disconnection in category III overvol-
tage conditions, must be equipped with a 
disconnection device incorporated in the fixed 
connection in compliance with the connection 
regulations. 

Use gloves suitable for cold trays. 

During cleaning operations, especially of 
the condenser, always wear protective

gloves, glasses and masks for protection of 
the respiratory tract.

It is prohibited to remove the protections 
and safety devices in order to perform

routine maintenance.

The responsibility of the operations 
performed on the machine, ignoring

the indications stated in this manual, is imple-
mented by the user.

Do not store explosive substances such 
as spray cans with flammable propellant

inside the appliance.

Children should be supervised to ensure 
they do not play with the appliance.

Cleaning and maintenance by the user 
should not be performed by children 
without the supervision of an adult.

The machine is not intended for use in 
a potentially explosive environment. 
The manufacturer declines any liability

 if this note is not complied with. 

Climatic class: 
4

 (environmental temperature 30°C with 

relative humidity 55% non-condensing)

pursuant to Standards IEC EN 60335-1, IEC 
EN 60335-2-89, ISO 23953-2:2005(E)

Do not overload the machine beyond 
t h a t  i n d i c a t e d  b y  t h e  m a n u f a c t u r e r 
(3.5.2.  Loading the machine).
Maximum load per shelf: 10 kg

 

 

 

 

 

Summary of Contents for CP One

























Reviews: