background image

 Series eWAVE  

 

 

                   Page 11 

 

 

 

       LT286 April 09, 2020    

WARRANTY TERMS & CONDITIONS 

 

eWAVE ELECTRIC INFRARED HEATERS 

WARRANTY TERMS & CONDITIONS 

 

The manufacturer warrants to the original owner that the product will be free of defects in the material and 
workmanship. This warranty is limited to 12 months from the date of installation for all components. 
 
The Manufacturer’s obligation under this warranty is limited to repair or replacement, F.O.B. the factory, of the 
defective part. In the case of replacement parts, the warranty period shall be the longer of the original warranty or 
a period of 12 months from the date of purchase. In no event shall the Manufacturer be liable for incidental 
expense or consequential damages of any kind. 
 
This warranty does not cover any shipping, installation or other costs incurred in the repair or replacement of the 
product. No materials will be accepted for return without authorization. 
 
This warranty will not apply if in the judgment of the Manufacturer, the equipment has been improperly installed, 
unreasonably used, damaged or modified. This warranty will not apply to damage to the product when used in 
corrosive atmospheres and in particular atmospheres containing halogenated hydrocarbons. No person is 
authorized to assume for the Manufacturer any other warranty, obligation or liability.  
 
Provision of this warranty is subject to: 

• 

The eWAVE product must be installed in accordance with the installation instructions and relevant 
electrical standards and codes. 

• 

The eWAVE product must be maintained and cleaned according to instructions detailed in the installation 
manual. 

• 

Discoloration of the surface may occur after a period of time; this does not constitute a warrantable event. 

 
Should products be determined as damaged on arrival, immediately notify the transport company of the condition 
and have them noted on the freight documents. If damage is discover after unpacking, demand immediate 
inspection by the transportation company and insist that a record of the damage is made on the freight 
documentation. 
 
The customer warrants using the product in accordance with: 

• 

Any instructions provided to it by Superior Radiant Products from time to time. 

• 

All government and local regulations, including but not limited to all relevant electrical, environmental laws 
and regulations governing the installation, storage, use, handling and maintenance of the goods. 

• 

All necessary and appropriate precautions and safety measures relating to the installation, storage, use, 
handing and maintenance of goods. 

 
THE REMEDIES PROVIDED FOR IN THE ABOVE EXPRESS WARRANTIES ARE THE SOLE AND EXCLUSIVE 
REMEDIES. NO OTHER EXPRESS OR IMPLIED WARRANTIES ARE MADE INCLUDING, BUT NOT LIMITED 
TO, ANY IMPLIED WARRANTY OF MERCHANT ABILITY OR FITNESS FOR A PARTICULAR USE OR 
PURPOSE. 
 

 
 
 
 
 
 
 
 

Summary of Contents for EW15L12













Reviews: