IQ PBX600 User Manual Download Page 33

Page: 33 / 134

www.yeastar.com

Page 33

IQ PBX 600 User Manual

standard port number used by IAX protocol. Do not change this part if it is not
required.

·Maximum Channels

Controls the maximum number of outbound channels (simultaneous calls) that
can be used on this trunk . Inbound calls are not counted against the maximum.
Leave blank to specify no maximum.

·Codecs

Define the codec for this sip trunk and its priority

Note

: codec is only displayed when edited it after creating the trunk.

·Transport

This will be the transport method used by the SIP Trunk. This method is given by
the SIP trunk provider. The options are UDP (default) or TCP or TLS.

·Qualify

Send check alive packets to the sip provider.

·DTMF mode

Set default mode for sending DTMF of this trunk. Default setting: rfc2833

DOD Setting

·DOD

Direct Outward Dialing Number.

·Associated Extension

The extension making a call out via BRI Trunk will display the associated DOD.

Summary of Contents for PBX600







































































































































Search results

Summary of Contents for PBX600

Reviews:

Related manuals for PBX600

Brands by name

Popular brands

IQ PBX600, User Manual

Search results

Summary of Contents for PBX600

Reviews:

Related manuals for PBX600

Brands by name

Popular brands