background image

MIG-160ER 

 

 

15 

 

Warranty Conditions 

The warranty and service are valid only with the invoice. 

 

1.1. Guarantor 

The guarantor is the company: 

IPO Technik-Handels GmbH 
Otto-Lilienthal-Str. 4 
88046 Friedrichshafen 
Germany 
Email: [email protected] 
Website: www.ipotools.eu 

The guarantee has to be claimed against the guarantor. 
 
1.2. Personal Scope of Application 

The guarantee applies equally to entrepreneurs and consumers 

1.3. Territorial Scope 

The guarantee is valid in the area of the EU member states. 

 

2.  ADDITIONAL MANUFACTURER WARRANTY 

For equipment delivered on or after April 29th, 2021, in addition to the statutory claims for defects under 
the German Civil Code (BGB), a 7-year durability  guarantee as defined in § 443 of the German Civil 
Code  (BGB)  applies  in  accordance  with  the  warranty  conditions  below.  For  devices  that  have  been 
delivered by IPO Technik-Handels GmbH until 29.04.2021, the previous warranty of 2 years applies. 

After 2 years, you still get the 5-year guarantee, which relates to the components defined under point 2 
“Technical Scope”. 
 
The  warranty  refers  to  components  which  are  inside  the  device,  especially  the  circuit  board  and  the 
inverter. It does not include the housing, the components of the housing as well as connections, ground 
cables and hose packages. It also does not cover the accessories and wearing parts supplied. 

2.1. Material Scope of Application 

The  seven-year  warranty  applies  only  to  electronic  welding  machines  and  plasma  cutters  of  the 
IPOTOOLS brand, which were delivered by IPO Technik-Handels GmbH on or after April 29th, 2021. 
The warranty does not apply to equipment sold as B-goods or used equipment. 

2.2. Technical Scope 

The warranty covers the components located in the housing of the device, in particular the circuit board 
and the inverter. It does not cover the housing, the components of the housing, the LCD display as well 
as  connections,  ground  cables,  electrode  holders  and  hose  packages.  It  also  does  not  include  the 
accessories and wearing parts supplied. 

2.3. Contents of the Warranty Claim 

The warranty grants a right to free repair of any damaged parts covered by the warranty. 

2.4. Right of Subsequent Delivery 

IPO Technik-Handels GmbH is entitled to deliver a new device instead of repair. 

Summary of Contents for MIG-160ER


















Reviews: