manualshive.com logo in svg

IOtech Digital HS, User Manual

Share
Download
IOtech Digital HS User Manual Download Page 9

Getting Started

2.1  Inspection

The Digital488HS/32 was carefully inspected, both mechanically and electrically,
prior to shipment.  After receiving the Digital488HS/32, carefully unpack all items
from the shipping carton and check for any obvious signs of physical damage. Report
any such damage found to the shipping agent immediately. Retain all shipping
materials in the event that shipment back to the factory is necessary.

Every Digital488HS/32 is shipped with the following items:

• Digital488HS/32

High Speed Digital I/O Interface

• DigitalHS-901

Instruction Manual

• 167-0800

Accessory Kit, which includes:

CA-1

Power Cable

FU-1-.25

1/4 Amp Replacement Fuse

FE-1

Rubber Feet (4)

EN-6

Rack Ears (2)

HA-41-6

Rack Ear Screws (4)

CN-19-37

37 Pin Male Connectors (2)

CN-17-37

Hood for CN-19-37 (2)

2.2  Configuration

The Digital488HS/32 has one external eight position switch, accessible from the rear
panel, and four internal eight position configuration switches (S2, S3, S4 and S5).

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for Digital HS



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands