manualshive.com logo in svg

IOtech Digital HS, User Manual, Page: 11 / 58

Share
Download
IOtech Digital HS User Manual Download Page 11

2.2.2  Internal Switch Settings

The internal settings on the Digital488HS/32 are for the line voltage, input and output
settings and the PTO default settings.

WARNING

Disconnect the power cord from the ac line and
from the Digital488HS/32 prior to disassembly.
Disconnect any cables prior to disassembly.

WARNING

Never open the Digital488HS/32 case while it is
connected to the ac line. Failure to observe this
warning may result in equipment failure,
personal injury or death.

Place the interface on a flat surface. Remove the four (4) screws located at each
corner. Carefully remove the top cover. Modify the parameters appropriate for your
installation and carefully re-assemble the interface using the reverse of the procedure
described.

2.2.2.1 Line Voltage Selection

The Digital488HS/32 may be operated from 110 or 220 V ac. The unit was shipped
from the factory set for the operating voltage marked on the label placed over the
power jack on the rear panel. To change the operating voltage, change the setting ot
internal switch S7 according to the following instructions.

WARNING

The Digital488HS/32 is intended for INDOOR
USE ONLY. Failure to observe this warning
could result in equipment failure, personal
injury or death.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for Digital HS



























































Reviews:

No comments